Subject	I've tossed out 2 sets of old school Stillen slip box units
Posted by	Bernie (NoVA) on December 02, 2016 at 8:15 PM
	This message has been viewed 499 times.
In Reply To	Thanks for the insight. OEM arms it is. (n/m) posted by zquikone on November 29, 2016 at 11:47 AM
Message	... in the past year. Same type of failure in both cases. Urethane bushings have dried and collapsed and the arms are rusted and seized. In both cases stock arms with standard 300Degree shim kit was enough to get in spec camber. Sometimes it's best not to over think it. Next week I'm replacing an entire engine front cross member / cradle because some misguided shop installed some kind of cam bolts onto the front lower arms and willow ed out the bolt holes. Now everytime you align the car the settings slip. Bernie Bilski berniebilski@cox.net President of Z-Car Club of Northern Virginia 1995 Nissan 300ZX TwinTurbo in Cobalt Green 1997 Nissan 240SX SE in Ultra Red 2006 Nissan Frontier SE in Ultra Black
Follow Ups	Front Upper Control Arm Options? - sak01 19:42:01 11/22/16 I like my UAS set... - Ted (92TT) 22:53:58 11/22/16 Re: I like my UAS set... - VinZmax 07:13:07 11/23/16 Yes there's a bearing on the axial portion... - Ted (92TT) 11:11:56 11/23/16 Good luck getting them. I tried getting the road/race - MixManMash 07:19:33 11/23/16 That sucks. Definitely worth the money if you want solids. (n/m) - Ted (92TT) 11:13:32 11/23/16 shim kit with new stock FUCA (n/m) - Bernie (NoVA) 01:22:59 11/23/16 2nd for your setup, this is the way to go (n/m) - WhiTTe Z 08:28:32 11/23/16 I 100% agree as well. - Goldchocobo 01:18:53 11/24/16 Shims with old stock FUCA & new Whiteline bushings. (n/m) - xpwarrior 09:18:02 11/24/16 Exactly what I want to do too. (n/m) - zquikone 12:26:12 11/24/16 Is there anything special regarding the Whiteline bushing - sak01 08:17:48 11/25/16 They were just much cheaper than buying new stock FUCAS. (n/m) - xpwarrior 19:53:28 11/25/16 The whiteline eccentric kit is a nice option if you want - black300zx 08:27:16 11/25/16 They don't fit. I went through 3 sets with them - BlackholeZ 11:21:48 11/25/16 The W51219 bushings? Mine fit fine and have - xpwarrior 19:55:05 11/25/16 Had to go back to my emails to check - BlackholeZ 00:56:29 11/29/16 False - the OEM bushings are better. (n/m) - Bernie (NoVA) 19:54:19 11/25/16 True - OEM may be better but Whiteline is still an option. (n/m) - xpwarrior 19:56:59 11/25/16 whitelines about about 160?$ its easier to just replace the - Dane (Houston) 10:51:38 11/28/16 Thanks for the insight. OEM arms it is. (n/m) - zquikone 11:47:08 11/29/16 I've tossed out 2 sets of old school Stillen slip box units - Bernie (NoVA) 20:15:09 12/02/16 ... - Bernie (NoVA) 20:20:59 12/02/16 Re: Front Upper Control Arm Options? - sak01 11:24:02 11/23/16 Yes, the long bolts need the extra space to insert. - jzack 13:56:02 11/23/16 You're being overly cautious. I move them all the time w. n - Bernie (NoVA) 19:01:33 11/23/16 No, you can unbolt the master w/ fluid lines attached and - Bernie (NoVA) 19:00:17 11/23/16 Re: No, you can unbolt the master w/ fluid lines attached and - sak01 21:59:04 11/23/16 Got them installed last night - sak01 09:07:40 11/26/16 Got the alignment done this morning - sak01 12:41:50 11/27/16 Enjoy (n/m) - Bernie (NoVA) 15:18:46 11/30/16 any pics available of the stock ones installed? - sak01 23:13:01 11/23/16 The side w. the L or R goes inboard. (n/m) - Bernie (NoVA) 19:57:30 11/25/16 KTS at RHD japan currently on sale - Dane (Houston) 17:23:12 11/23/16
Post a Followup	You cannot reply to this message because you are not logged in.