Subject	Couldn't I get the same results?
Posted by	scarlet on June 29, 2016 at 12:14 AM
	This message has been viewed 451 times.
In Reply To	You could but the Neo can do the same thing the Selin does. posted by Bernie (NoVA) on June 28, 2016 at 11:41 PM
Message	Couldn't I get the same results if I left the selin translator hooked up and just hooked up the neo? So I wouldn't have to run any wires? Since the selin is already taking the two maf readings and sending it to the ecu like the neo would. So wouldn't the neo just intercept the selin signal and allow me to adjust it I suppose then send it to the ecu?
Follow Ups	selin dual maf and apexi neo? - scarlet 23:11:06 06/28/16 You could but the Neo can do the same thing the Selin does. - Bernie (NoVA) 23:41:17 06/28/16 Couldn't I get the same results? - scarlet 00:14:26 06/29/16 Yes but it's a waste of money & adds layers of failure point (n/m) - Bernie (NoVA) 07:34:01 06/29/16 Re: Yes but it's a waste of money & adds layers of failure point - scarlet 13:36:27 06/29/16 This is the worst possible way to tune. Modifying the air - MixManMash 14:57:41 06/29/16 Additionally, if it's running "rich," have you checked for - MixManMash 14:58:51 06/29/16 Why would you do that? There is absolutely no sane reason - MixManMash 08:13:35 06/29/16 Ive always been curious about that... - -Grimm- 09:55:09 06/29/16 well.. - Antihero 13:40:25 06/29/16 Exactly. The MAF sensor is non-linear. (n/m) - MixManMash 14:53:57 06/29/16 Re: Exactly. The MAF sensor is non-linear. - scarlet 15:15:15 06/29/16 Ouch! Sounds like you have bigger problems. (n/m) - MixManMash 16:09:32 06/29/16 Re: Exactly. The MAF sensor is non-linear. - scarlet 15:30:45 06/29/16 Anyone ever take one apart? - -Grimm- 19:13:41 06/29/16 if it's still in the box, sell the neo and get nistune. - Antihero 23:50:40 06/28/16 This - BlackholeZ 13:16:11 06/29/16 Agreed, but an off-the-shelf chip is not the same as a - MixManMash 14:58:16 06/29/16 Very true - BlackholeZ 02:54:48 06/30/16 ======Answers... - DVDBURN (MD) 01:40:56 07/01/16 The ECU interpolates MAF VQ table values - zromtech 13:53:19 07/01/16 In my experience it doesn't switch to the next table... - DVDBURN (MD) 15:50:56 07/01/16 To add...the interpolation is used to tell where in the... - DVDBURN (MD) 16:04:35 07/01/16 To try to make this even more simple... - DVDBURN (MD) 11:38:38 07/02/16 Re: To try to make this even more simple... - zromtech 12:19:33 07/02/16 but interpolation happens after the table lookup - zromtech 12:12:21 07/02/16 I'm talking about how the ECU knows how to place the MAF... - DVDBURN (MD) 19:26:25 07/02/16 CFM Table? - zromtech 09:49:05 07/03/16 I'm not saying that. - DVDBURN (MD) 14:21:22 07/03/16 Re: I'm not saying that. - zromtech 18:33:16 07/03/16
Post a Followup	You cannot reply to this message because you are not logged in.