Subject	Harbor Freight sells a 6 and 20 gallon parts washer, they
Posted by	SirpriZ on March 01, 2015 at 12:52 PM
	This message has been viewed 184 times.
In Reply To	What solvent do machine shops use to clean parts? posted by OverZealous (CT) on March 01, 2015 at 09:47 AM
Message	are $45 and $100 respectively. You can soak your parts in the washer. Mineral spirits (paint thinner, etc) are as effective a solvent as anything else, and the least expensive, it just stinks. I use Brakleen from 1 gallon bottles in the parts washer.
Follow Ups	What solvent do machine shops use to clean parts? - OverZealous (CT) 09:47:29 03/01/15 They use a hot tank - -Grimm- 11:07:52 03/01/15 2nd (n/m) - Dallas DamonZ 12:01:09 03/01/15 Yup. Took a set of heads to NAPA and it cost 25 to hot - white22sky 12:04:47 03/01/15 NAPA around here doesn't have one (lame). - OverZealous (CT) 12:44:53 03/01/15 So the shop I recommended sucked? Sorry dude - BigTDogg (MA) 15:59:41 03/02/15 I had a GREAT experience with him... - OverZealous (CT) 22:01:46 03/02/15 OK, that's a relief. - BigTDogg (MA) 22:22:24 03/02/15 Re: OK, that's a relief. - OverZealous (CT) 19:43:51 03/03/15 Harbor Freight sells a 6 and 20 gallon parts washer, they - SirpriZ 12:52:50 03/01/15 Are mineral spirits safe? Hotsy? Red Devil Lye (equiv)? - OverZealous (CT) 13:53:07 03/01/15 Have the 6 gallon one - Lumpydonut 07:42:18 03/02/15 My recommendation for DIY: - BoneZ (MD) 14:21:01 03/01/15 Nice video! Thanks. - OverZealous (CT) 14:38:55 03/01/15 I used that sprayer with diluted MArine Clean - BoneZ (MD) 15:19:15 03/01/15 You want to use mineral spirits in a ventilated area, but - SirpriZ 15:23:12 03/01/15 Oops, meant to reply to OP. (n/m) - SirpriZ 18:31:21 03/01/15 NP- brings up a good point. Also Marine Cln isn't petro base (n/m) - BoneZ (MD) 09:03:19 03/02/15 Hot tank or jet wash at a machine shop - ZXRider 14:55:34 03/01/15 Huh? Hot tanks aren't available anymore in SoCal? (n/m) - OverZealous (CT) 16:36:46 03/01/15 They're becoming scarce in CA in general. - BlackholeZ 18:03:10 03/01/15 $125/hr is going rate in CT for spray wash - OverZealous (CT) 14:54:56 03/02/15 I have a Carolina Parts Washer and I bought a pail of - davidztt 15:16:52 03/01/15 sonic cleaning > everything (n/m) - Madhatter10-6 15:22:20 03/01/15 Right!! But whose got one? (video) - OverZealous (CT) 17:02:21 03/01/15 My engine guy 10 minutes from the house :) (n/m) - Madhatter10-6 18:25:44 03/01/15 We use zymeflow. (n/m) - ZaXxon 16:48:39 03/01/15 How about a link on where to buy? (n/m) - OverZealous (CT) 17:07:18 03/01/15 For DIY I recommend soda blasting - bartz32tt 21:01:15 03/01/15
Post a Followup	You cannot reply to this message because you are not logged in.