Subject	I'll probably pick up those prybars I mentioned
Posted by	BlackholeZ on February 25, 2015 at 11:58 AM
	This message has been viewed 334 times.
In Reply To	Heavily Discounted Snap On Tools for my fellow Z'ers posted by Evan(CA) on February 25, 2015 at 02:40 AM
Message	I'll shoot you an email. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Heavily Discounted Snap On Tools for my fellow Z'ers - Evan(CA) 02:40:09 02/25/15 How much for that 36" 1/2" drive extension bar needed to - davidztt 03:19:25 02/25/15 Please read the entire post. - Evan(CA) 03:44:05 02/25/15 http://www.ttzd.com/tech/enginetech.html - davidztt 13:49:12 02/25/15 I've done many transmission pulls... switched from 1/2" - vorpalZ 14:07:24 02/25/15 I think if Damon feels that a 3/8" drive bar would suffice, - davidztt 14:12:33 02/25/15 chuckle, and I'm saying that for the several I have pulled - vorpalZ 14:16:18 02/25/15 No biggie. I found it. Any opinions on Sunex? - davidztt 14:27:34 02/25/15 It will get the job done. - Evan(CA) 14:53:35 02/25/15 no kidding. (n/m) - Dallas DamonZ 16:39:42 02/25/15 I have this one from Sunex: - Tanley 19:10:46 02/25/15 2nd, I start with 18" of 1/2" drive and neck down to 3/8" - BigTDogg (MA) 17:00:34 02/26/15 3rd (n/m) - OverZealous (CT) 11:59:39 02/28/15 Re: http://www.ttzd.com/tech/enginetech.html - Dallas DamonZ 14:11:23 02/25/15 Thanks, Damon. I'm 5'8" on a good day, weigh 190 lbs (no, - davidztt 14:20:02 02/25/15 Re: Thanks, Damon. I'm 5'8" on a good day, weigh 190 lbs (no, - Dallas DamonZ 14:27:48 02/25/15 BAHAHAHA! Hey, how did you know I'm a tongue-worker? - davidztt 14:34:59 02/25/15 whoa, out-of-context sig quote material alert! (n/m) - LJZTT 20:04:23 02/25/15 ??? It's all in your mind. (n/m) - davidztt 01:21:24 02/26/15 Damon, this is a blind guess but do you suppose that if you - davidztt 01:32:58 02/26/15 Not going to work. (n/m) - Bernie (NoVA) 01:55:11 02/26/15 Ok thanks, Bernie. What's in the way? Shield or something? (n/m) - davidztt 02:25:57 02/26/15 The floor. No angle. The 3' Extension is tried and true. (n/m) - Nate (NoVA) 08:22:29 02/26/15 Hai. (n/m) - Bernie (NoVA) 10:12:11 02/26/15 -Karate? ;-) What's that mean? lol (n/m) - davidztt 14:04:03 02/26/15 . - Bernie (NoVA) 20:35:08 02/26/15 dang. I didn't realize the tunnel is so close to the top of - davidztt 14:10:02 02/26/15 Not going to work at all or just not with 1 person? - evan_aggie 12:51:44 02/26/15 Alternatively: loosen mounts, disconnect hoses and wires, - Hiram 02:53:12 02/26/15 This sounds promising. The transmission is coming - davidztt 14:07:13 02/26/15 I mean un-bolt the transmission from it's mount. (n/m) - davidztt 14:28:43 02/26/15 Nevermind. Apparently Snap-On doesn't have the extension bar - davidztt 14:06:47 02/25/15 You are probably looking at chrome extensions which are - Evan(CA) 14:35:03 02/25/15 Yeh I looked under BluePoint but I didn't see one that long. - davidztt 14:38:15 02/25/15 lol Snap on definitely has the extension you are - John (MD) 20:23:31 02/25/15 Yeh apparently some Sunex tools are re-badged as Snap-On, - davidztt 01:20:00 02/26/15 Still hopin you'll reply with that webpage (?) (n/m) - davidztt 22:08:45 02/28/15 I'm interested as well. (n/m) - ILoveBoost 07:29:24 02/25/15 Nice, I need a few things. Thanks again Evan. (n/m) - Schmeal (NV) 08:56:31 02/25/15 email sent, thanks! (n/m) - boileralum 10:08:18 02/25/15 I'll probably pick up those prybars I mentioned - BlackholeZ 11:58:36 02/25/15 Don't wait around and miss the boat like you did with that - Evan(CA) 12:14:14 02/25/15 That's odd. The "Country of Origin" for some Snap-On tools - davidztt 13:57:29 02/25/15 Email sent... (n/m) - rcmadness 16:01:13 02/25/15 OMG! OMG! I'll be requesting these: FHOM606B - apudapus 20:20:33 02/25/15 Email sent. Thanks Evan! (n/m) - James_Z32 20:25:25 02/25/15 Do you know if ratchet rebuild kits are available? - dogpile 09:14:58 02/26/15 Have you tried getting a warrantied replacement? - bartz32tt 09:25:54 02/26/15 I haven't tried yet, no. I haven't seen a local SO dealer - dogpile 09:29:23 02/26/15 Unfortunately I don't deal with the usual truck dealer. - Evan(CA) 10:05:38 02/26/15 I know, that's why I asked if you could get a rebuild kit. - dogpile 11:45:43 02/26/15 Can be rebuilt on the truck in 5 min or less. (n/m) - Bernie (NoVA) 20:38:52 02/26/15 Very much appreciated, will have to do a quick inventory and - BigTDogg (MA) 15:29:43 02/26/15 Careful, tool buying is addictive. - Evan(CA) 20:10:22 02/26/15 Well, the thing that sucks is when you walk through a - davidztt 06:04:22 02/27/15 You wont get any sympathy from me for that :) - Evan(CA) 19:01:32 02/27/15 TORQUE WRENCH 1/2" Ratchet 150 or 250 ft-lb - OverZealous (CT) 12:53:49 02/28/15
Post a Followup	You cannot reply to this message because you are not logged in.