Subject	Re: even if this is true - the OEM knock control only works
Posted by	zromtech on February 21, 2015 at 11:08 AM
	This message has been viewed 413 times.
In Reply To	even if this is true - the OEM knock control only works posted by The Devils Z on February 20, 2015 at 07:15 PM
Message	The OEM knock control system does work for the entire RPM band. It listens for knock at lower RPM and then calculates how much timing to pull at high rpm based on that. For the record, there are *lots* of other glitches like this in big injector tunes... long-term O2 self-learn, VTC, MAF fail-safe mode, cranking injector pulsewidth (some 740cc tunes dump 2x too much fuel during cranking, lol), catalyst warm-up maps, hysteresis values... the list goes on. Only the 370cc injector guys know how smoothly these cars should really run. Can you un-plug your MAF, start your car and drive away normally (up to 2500rpm) with no bucking or stalling?? You should be able to.
Follow Ups	Rod bearing service life:a long-term review of my experience - Ash's Z 06:24:41 02/20/15 Why not just run less aggressive timing to lower - The Devils Z 08:14:52 02/20/15 I've been running 18 degrees of total advance at full load - Ash's Z 11:54:37 02/20/15 You can have gradual detonation without hurting - The Devils Z 19:26:49 02/20/15 i use the JS knock box you can hear knock that you can not - Dane (Houston) 18:52:13 02/23/15 Re: Mobil 1 - Hiram 08:40:41 02/20/15 Hmm. (n/m) - BannonZ 09:02:53 02/20/15 I dont think Ash mentioned anything about the EP oil - ZXoltan 10:44:19 02/20/15 C&D Recommends Changing Your Oil at Least Twice a Year - flashstar 11:53:40 02/20/15 You're correct. Oil's life is measured not only by mileage, - Hiram 00:11:56 02/21/15 I change the engine oil every 3K miles bud. Keep in mind, - Ash's Z 11:57:26 02/20/15 Wear could be worse on the 6th in general but good oil - flashstar 12:01:30 02/20/15 So if Mobil 1 15K mile oil falls back to a manufacturer's - Hiram 13:37:49 02/20/15 people say all sorts of crap based on nothing but suspicion (n/m) - LJZTT 13:52:49 02/20/15 Truth! (n/m) - Barry (NJ) 14:20:06 02/20/15 my life at work .. probably the best comment I have - The Devils Z 19:20:22 02/20/15 I would quit a job like that, lol (n/m) - Hiram 23:47:28 02/20/15 I wouldn't deny someone's experience with a product, but - Hiram 00:02:18 02/21/15 it has nothing to do with fine print vs marketing print - LJZTT 13:11:42 02/22/15 I will tell them to tell their mechanics what you said. (n/m) - Hiram 02:21:30 02/26/15 Like I said, best of luck :) (n/m) - Hiram 13:41:37 02/20/15 BTW, I'm not using Extended Performance lube. (n/m) - Ash's Z 16:15:27 02/20/15 Understood. Good luck with it. (n/m) - Hiram 23:48:16 02/20/15 Do you know if shimming the oil pump pressure relief valve - ZXRider 10:47:52 02/20/15 There was no indication of that being the case. I caught - Ash's Z 15:27:57 02/20/15 Do you think this feeds back to #6 running hotter? - Schmeal (NV) 11:05:23 02/20/15 Your proposal is based on piston sieze which I am sure is - Ash's Z 16:18:57 02/20/15 One of the best "knock boxes" out there... - kickerzx 17:53:30 02/20/15 Like the post and timely.... - Z ONLY1 11:11:25 02/20/15 Is your OEM knock control in spec? - zromtech 11:48:05 02/20/15 even if this is true - the OEM knock control only works - The Devils Z 19:15:35 02/20/15 His thread on the subject back in 2013... - Ted (92TT) 20:26:13 02/20/15 Re: even if this is true - the OEM knock control only works - zromtech 11:08:16 02/21/15 Interesting - maglito 21:51:36 02/23/15 What EMS? - bartz32tt 12:06:06 02/20/15 Which EMS can write specifically to an individual injector?? (n/m) - RZturbo 20:41:28 02/20/15 Most decent ones can... (n/m) - kickerzx 05:45:08 02/21/15 Do you have a UOA done at each oil change? - Tanley 18:49:33 02/20/15 I run 20W50 - RZturbo 20:54:40 02/20/15 Do you run 20W50 in the winter also? (n/m) - sak01 11:02:20 02/21/15 The z is normally garaged - RZturbo 20:35:26 02/21/15 I really like M1 5w50 (n/m) - Polish 02:33:21 02/22/15 Re: Rod bearing service life:a long-term review of my experience - Bigwill837 08:25:10 02/21/15 You went with 0.0015" bearing clearance - -Grimm- 09:56:13 02/21/15 seems a bit tight to me - aliaZ 17:43:19 02/22/15 2nd (n/m) - John (MD) 15:36:57 03/01/15 Ash, exactly which oil are you using? Any sampling? - SMAZ (OKC) 12:23:50 02/22/15 Thanks for sharing your findings Ash! (n/m) - maglito 21:52:47 02/23/15
Post a Followup	You cannot reply to this message because you are not logged in.