Subject	You went with 0.0015" bearing clearance
Posted by	-Grimm- on February 21, 2015 at 9:56 AM
	This message has been viewed 298 times.
In Reply To	Rod bearing service life:a long-term review of my experience posted by Ash's Z on February 20, 2015 at 06:24 AM
Message	on an engine you built for performance (and semi-harsh conditions)? ------------------------------------------------------------------ 1992 300ZX NA 5 Sp (Dead) 1990 300ZX NA Auto 2+2 (Dead) 1990 300ZX TT 5 Sp (Est. 400 HP) 1990 300ZX TT 5 Sp (Est. 600 HP) 2004 G35 Sport 6MT (DD)
Follow Ups	Rod bearing service life:a long-term review of my experience - Ash's Z 06:24:41 02/20/15 Why not just run less aggressive timing to lower - The Devils Z 08:14:52 02/20/15 I've been running 18 degrees of total advance at full load - Ash's Z 11:54:37 02/20/15 You can have gradual detonation without hurting - The Devils Z 19:26:49 02/20/15 i use the JS knock box you can hear knock that you can not - Dane (Houston) 18:52:13 02/23/15 Re: Mobil 1 - Hiram 08:40:41 02/20/15 Hmm. (n/m) - BannonZ 09:02:53 02/20/15 I dont think Ash mentioned anything about the EP oil - ZXoltan 10:44:19 02/20/15 C&D Recommends Changing Your Oil at Least Twice a Year - flashstar 11:53:40 02/20/15 You're correct. Oil's life is measured not only by mileage, - Hiram 00:11:56 02/21/15 I change the engine oil every 3K miles bud. Keep in mind, - Ash's Z 11:57:26 02/20/15 Wear could be worse on the 6th in general but good oil - flashstar 12:01:30 02/20/15 So if Mobil 1 15K mile oil falls back to a manufacturer's - Hiram 13:37:49 02/20/15 people say all sorts of crap based on nothing but suspicion (n/m) - LJZTT 13:52:49 02/20/15 Truth! (n/m) - Barry (NJ) 14:20:06 02/20/15 my life at work .. probably the best comment I have - The Devils Z 19:20:22 02/20/15 I would quit a job like that, lol (n/m) - Hiram 23:47:28 02/20/15 I wouldn't deny someone's experience with a product, but - Hiram 00:02:18 02/21/15 it has nothing to do with fine print vs marketing print - LJZTT 13:11:42 02/22/15 I will tell them to tell their mechanics what you said. (n/m) - Hiram 02:21:30 02/26/15 Like I said, best of luck :) (n/m) - Hiram 13:41:37 02/20/15 BTW, I'm not using Extended Performance lube. (n/m) - Ash's Z 16:15:27 02/20/15 Understood. Good luck with it. (n/m) - Hiram 23:48:16 02/20/15 Do you know if shimming the oil pump pressure relief valve - ZXRider 10:47:52 02/20/15 There was no indication of that being the case. I caught - Ash's Z 15:27:57 02/20/15 Do you think this feeds back to #6 running hotter? - Schmeal (NV) 11:05:23 02/20/15 Your proposal is based on piston sieze which I am sure is - Ash's Z 16:18:57 02/20/15 One of the best "knock boxes" out there... - kickerzx 17:53:30 02/20/15 Like the post and timely.... - Z ONLY1 11:11:25 02/20/15 Is your OEM knock control in spec? - zromtech 11:48:05 02/20/15 even if this is true - the OEM knock control only works - The Devils Z 19:15:35 02/20/15 His thread on the subject back in 2013... - Ted (92TT) 20:26:13 02/20/15 Re: even if this is true - the OEM knock control only works - zromtech 11:08:16 02/21/15 Interesting - maglito 21:51:36 02/23/15 What EMS? - bartz32tt 12:06:06 02/20/15 Which EMS can write specifically to an individual injector?? (n/m) - RZturbo 20:41:28 02/20/15 Most decent ones can... (n/m) - kickerzx 05:45:08 02/21/15 Do you have a UOA done at each oil change? - Tanley 18:49:33 02/20/15 I run 20W50 - RZturbo 20:54:40 02/20/15 Do you run 20W50 in the winter also? (n/m) - sak01 11:02:20 02/21/15 The z is normally garaged - RZturbo 20:35:26 02/21/15 I really like M1 5w50 (n/m) - Polish 02:33:21 02/22/15 Re: Rod bearing service life:a long-term review of my experience - Bigwill837 08:25:10 02/21/15 You went with 0.0015" bearing clearance - -Grimm- 09:56:13 02/21/15 seems a bit tight to me - aliaZ 17:43:19 02/22/15 2nd (n/m) - John (MD) 15:36:57 03/01/15 Ash, exactly which oil are you using? Any sampling? - SMAZ (OKC) 12:23:50 02/22/15 Thanks for sharing your findings Ash! (n/m) - maglito 21:52:47 02/23/15
Post a Followup	You cannot reply to this message because you are not logged in.