Subject	Thanks
Posted by	BlackholeZ on November 28, 2014 at 5:12 PM
	This message has been viewed 452 times.
In Reply To	I've been looking at these too. posted by Polish on November 28, 2014 at 03:15 PM
Message	I'm not sure if I want/need the adjustability. I've got some friends that might though. I actually really like the ~2.5° that I've got with the stock arms, it's just the stock bushings are shot. -Dan VTC Solenoid Caps and install instructions. "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne " Purrs like a sexually satisfied black panther." - BigTDogg "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	Best adjustable FUCAs? - evan_aggie 07:42:29 11/27/14 Stillen arm has its own issues - LJZTT 10:39:10 11/27/14 That's the old design. (n/m) - ali300zx 11:00:23 11/27/14 roger - LJZTT 20:55:35 11/27/14 Re: Best adjustable FUCAs? - ttz'in (NorCal) 13:12:36 11/27/14 UAS - Still available apparently: - MixManMash 13:47:51 11/27/14 yes, always available direct. (n/m) - lidz 14:14:26 11/27/14 probably these.expensive though. - slayer fan 21:11:12 11/27/14 Nope. UAS is the best. (n/m) - MixManMash 06:41:56 11/28/14 anything wrong with z1? (n/m) - evan_aggie 09:00:12 11/28/14 Not sure, but I wouldn't trust anything they put out. - MixManMash 13:38:40 11/28/14 This would be a much better statement - VERTTZ 10:05:49 11/28/14 I's a bearing design that also pivots axially. (n/m) - Ted (92TT) 11:11:12 11/28/14 it allows travel on the third axis that others don't - vorpalZ 11:22:00 11/28/14 I figured Z1 was alright bc it had bushings too? (n/m) - evan_aggie 11:25:14 11/28/14 There are Two Versions of the Z1 FUCA - flashstar 12:12:02 11/28/14 If you only need a little bit of one-time adjustability, - black300zx 12:04:03 11/28/14 Problem is that the OEM FUCAs wear out after time as well. - MixManMash 13:37:31 11/28/14 I think the point is that the whiteline bushings replace - BlackholeZ 14:42:01 11/28/14 The worn OEM bushings get replaced with the kit. Or are you - black300zx 23:07:52 11/29/14 You have a link? - BlackholeZ 14:45:02 11/28/14 I've been looking at these too. - Polish 15:15:01 11/28/14 Thanks - BlackholeZ 17:12:53 11/28/14 Sorry, I thought it was obvious about the rotation. - MixManMash 13:39:40 11/28/14 Inherent design fault in this type of FUCA..... - zx299 17:58:40 11/29/14 This. I started noticing play in mine and no amount of - MixManMash 21:54:13 11/29/14
Post a Followup	You cannot reply to this message because you are not logged in.