Subject	it allows travel on the third axis that others don't
Posted by	vorpalZ on November 28, 2014 at 11:22 AM
	This message has been viewed 541 times.
In Reply To	This would be a much better statement posted by VERTTZ on November 28, 2014 at 10:05 AM
Message	which results in wear and failure of the other FUCA designs. Stock non-adjustable allow some play with the rubber bushings, Stillen, Powertrix & Z1 don't. MY Zs ARE HYBRID VEHICLES, THEY RUN ON GASOLINE AND MONEY "I expressed no attitude, I'm correcting you. If you don't like it, try not to be wrong next time. Now you're getting attitude, and if you don't like that you should grow a thicker skin.” - TriniTT 14:04:16 12/22/12 ”Exhaust doesn't produce horsepower” - VERTTZ 13:17:22 06/26/12 I'm off to wax mine and go for a drive now. - BigTDogg (MA) 07:17:08 07/17/09 times change, people change, but the Z32 still kicks ass. - apudapus 16:46:02 06/15/07 I was more wondering how you set your climate control to 22* lol, it would be that fastest freezer on wheels! - Briscoe'sZ32 (NJ) 23:15:44 02/05/07 You have *got* to be getting a cut from B&B :D - SeedyROM 15:24:29 08/16/06 What do you think B&B stands for? - YugoBernie (NoVA) 15:57:09 08/16/06
Follow Ups	Best adjustable FUCAs? - evan_aggie 07:42:29 11/27/14 Stillen arm has its own issues - LJZTT 10:39:10 11/27/14 That's the old design. (n/m) - ali300zx 11:00:23 11/27/14 roger - LJZTT 20:55:35 11/27/14 Re: Best adjustable FUCAs? - ttz'in (NorCal) 13:12:36 11/27/14 UAS - Still available apparently: - MixManMash 13:47:51 11/27/14 yes, always available direct. (n/m) - lidz 14:14:26 11/27/14 probably these.expensive though. - slayer fan 21:11:12 11/27/14 Nope. UAS is the best. (n/m) - MixManMash 06:41:56 11/28/14 anything wrong with z1? (n/m) - evan_aggie 09:00:12 11/28/14 Not sure, but I wouldn't trust anything they put out. - MixManMash 13:38:40 11/28/14 This would be a much better statement - VERTTZ 10:05:49 11/28/14 I's a bearing design that also pivots axially. (n/m) - Ted (92TT) 11:11:12 11/28/14 it allows travel on the third axis that others don't - vorpalZ 11:22:00 11/28/14 I figured Z1 was alright bc it had bushings too? (n/m) - evan_aggie 11:25:14 11/28/14 There are Two Versions of the Z1 FUCA - flashstar 12:12:02 11/28/14 If you only need a little bit of one-time adjustability, - black300zx 12:04:03 11/28/14 Problem is that the OEM FUCAs wear out after time as well. - MixManMash 13:37:31 11/28/14 I think the point is that the whiteline bushings replace - BlackholeZ 14:42:01 11/28/14 The worn OEM bushings get replaced with the kit. Or are you - black300zx 23:07:52 11/29/14 You have a link? - BlackholeZ 14:45:02 11/28/14 I've been looking at these too. - Polish 15:15:01 11/28/14 Thanks - BlackholeZ 17:12:53 11/28/14 Sorry, I thought it was obvious about the rotation. - MixManMash 13:39:40 11/28/14 Inherent design fault in this type of FUCA..... - zx299 17:58:40 11/29/14 This. I started noticing play in mine and no amount of - MixManMash 21:54:13 11/29/14
Post a Followup	You cannot reply to this message because you are not logged in.