Subject	I've been working with the fabricator on these brackets
Posted by	JDAVE on September 24, 2014 at 12:47 PM
	This message has been viewed 365 times.
In Reply To	You might post some photos of the brake mounting brackets. posted by not4resaleZ on September 24, 2014 at 12:21 PM
Message	While they were designed as pretty much a bolt up affair for 240sx's, the Z required a washer on the top bolt and a very small spacer for the bottom no where near 1" I just didn't want to run 4 washers so we machined a spacer. I gave the specs to the fabricator and he will be sending me 3 brackets with these modifications so this kit will be more along the lines of a bolt up affair as well. Unfortunately I don't have any finished pictures of the set up but there are some on Facebook. This kit uses a 12.75" 350z rotor and I have them behind 17" wheels on this vehicle.
Follow Ups	Jamie's build - JDAVE 03:28:58 09/24/14 Isn't that the CTS-v brake kit we were talking about below? - BannonZ 07:05:06 09/24/14 lol, he tried to subtley make the distinction, but I'm sure - LJZTT 10:52:24 09/24/14 very nice - tell him to get head work & cams though! (n/m) - JaffaUK 07:18:06 09/24/14 We are going to do his heads next but for now he's happy. (n/m) - JDAVE 10:48:01 09/24/14 you know you don't need to take a picture of the dyno - ztunerz 09:02:51 09/24/14 :) :) :)......teaser...nice. (n/m) - Z ONLY1 09:31:28 09/24/14 Need to see the whole graph. - Woody75 (Denver) 09:50:04 09/24/14 Will post one soon :) (n/m) - JDAVE 10:52:16 09/24/14 kewl (n/m) - LJZTT 10:53:09 09/24/14 You might post some photos of the brake mounting brackets. - not4resaleZ 12:21:25 09/24/14 Re: You might post some photos of the brake mounting brackets. - Bad Fish 12:36:32 09/24/14 I've been working with the fabricator on these brackets - JDAVE 12:47:58 09/24/14 You use the word "designed". To many this would imply that - not4resaleZ 13:52:46 09/24/14 There is a difference between "designed" and "engineered." (n/m) - MixManMash 16:41:57 09/24/14 Well that may be a difference between mechanical - not4resaleZ 17:35:48 09/24/14 Re: Well that may be a difference between mechanical - ZXRider 18:06:28 09/24/14 FEA is only useful if you know what boundary conditions to - black300zx 18:31:20 09/24/14 That being said, there were plenty of critical parts - black300zx 18:42:36 09/24/14 2nd that - ZXRider 18:56:38 09/24/14 I'm not. I'd scratch it out on a piece of paper. (n/m) - not4resaleZ 20:46:03 09/24/14 I'd probably start with the shear capacity of the existing - not4resaleZ 21:30:09 09/24/14 That's right, garbage in = garbage out. - BigTDogg (MA) 13:01:15 09/26/14 Nah, you're just being a hater... - bartz32tt 14:47:52 09/26/14 Look here... - Barry (NJ) 13:31:33 09/24/14 Re: Jamie's build - WazTTed 18:01:23 09/24/14 mine - JaffaUK 03:23:20 09/25/14 Where did you get those smooth, tight radius 90* ANs? (n/m) - induetime 12:09:59 09/25/14 link inside - JaffaUK 13:11:00 09/25/14 Nice build and numbers! Would like to see the dyno chart. (n/m) - TheTwinZ (Peru) 23:52:29 09/25/14 I'll make a post with it. Dyno computer is getting upgraded - JDAVE 00:23:34 09/26/14
Post a Followup	You cannot reply to this message because you are not logged in.