Subject	Because you're not looking at the right part.
Posted by	TriniTT on July 19, 2014 at 3:23 PM
	This message has been viewed 132 times.
In Reply To	Sure doesn't look like 2mm in difference that your claiming (n/m) posted by toykoz32 on July 19, 2014 at 12:55 PM
Message	I keep repeating myself and this is the last time I'm going to respond. You're measuring the distance from the top of the clip to the bottom. If the top of the clip was the part that held the trim down, this would make sense. But it isn't. The arms that stick out the side of the clip are what holds the trim in place, and these are significantly different between the black and white clips. I can't help you any further, at this point nobody can. Cheers, JBrobst
Follow Ups	Roof trim clip part number for slicktops - TriniTT 22:12:31 07/17/14 Re: Roof trim clip part number for slicktops - Stadsport (Nick@CZP) 00:12:55 07/18/14 Re: Re: Roof trim clip part number for slicktops - MikeC(NZ) 01:15:16 07/18/14 For years I've slid a small piece of electrical wire down - TriniTT 07:15:32 07/18/14 I sanded down a white one and it has been working fine - toykoz32 12:13:41 07/18/14 That's not the same thing. - TriniTT 13:34:52 07/18/14 Dont know what to tell you. I sand a pair down - toykoz32 16:42:55 07/18/14 I doubt it did, but I'm anal about attention to detail. - TriniTT 16:45:08 07/18/14 Sooo you've tried it? not to anal with the electrical wire? (n/m) - toykoz32 16:49:48 07/18/14 Can you see the electrical wire? No, it's inside the trim. - TriniTT 17:22:48 07/18/14 I don't know, you didn't post a picture of your setup - toykoz32 18:10:05 07/18/14 No, because I understand how the clips function. - TriniTT 18:48:26 07/18/14 NOPE. once i get home i might have time to prove you are - toykoz32 18:54:32 07/18/14 I'd be happy to be proven wrong. (n/m) - TriniTT 19:22:45 07/18/14 Meth is bad. (n/m) - ForceFedTT (SoCal) 07:49:17 07/19/14 You'd know best. (n/m) - TriniTT 08:18:10 07/19/14 Lol! (n/m) - ForceFedTT (SoCal) 07:47:50 07/19/14 look at your first photo - toykoz32 16:45:36 07/18/14 No, it won't. Sorry but you're incorrect. - TriniTT 18:14:22 07/18/14 okay buddy, hope you find a solution. (n/m) - toykoz32 18:56:38 07/18/14 just measured and they are different but not by the - toykoz32 10:23:04 07/19/14 I posted a pic with the clear and obvious difference - TriniTT 11:21:34 07/19/14 Why are you so mad bruh? - toykoz32 11:25:02 07/19/14 You can't even distinguish the clip arms in your pics. - TriniTT 11:33:26 07/19/14 First pic looks clear enough for me. - toykoz32 12:53:00 07/19/14 The first pic you can't even tell where the retaining arms - TriniTT 15:20:16 07/19/14 Sure doesn't look like 2mm in difference that your claiming (n/m) - toykoz32 12:55:57 07/19/14 Because you're not looking at the right part. - TriniTT 15:23:32 07/19/14 I love how this turned into a huge online argument. (n/m) - CameronSF 15:14:57 07/21/14 Wow! Obsessive! (n/m) - ForceFedTT (SoCal) 07:46:35 07/19/14 Sorry, Looked at the one I did, and I plastic welded them. - toykoz32 10:04:08 07/20/14 Very nice, I considered this also, but wasn't sure if it - TriniTT 09:26:11 07/21/14 My buddy has a 3D printer. - J-Mart 14:13:08 07/18/14 Tell him to make a passenger cowl! - bartz32tt 16:47:04 07/18/14 Yes! (n/m) - ForceFedTT (SoCal) 07:53:33 07/19/14 hopefully this useless post gets deleted (n/m) - toykoz32 13:52:44 07/19/14 This post is actually full of helpful information. - TriniTT 15:09:34 07/19/14 nope, it serves no purpose at all unless you had a fix - toykoz32 15:22:00 07/19/14 I do have a fix, which I clearly explained. - TriniTT 15:25:24 07/19/14 why do you keep texting me? mad cause I disagree with you? - toykoz32 15:33:30 07/19/14 Yep (n/m) - TriniTT 15:46:41 07/19/14 My fix explained: - TriniTT 15:40:48 07/19/14
Post a Followup	You cannot reply to this message because you are not logged in.