TwinTurbo.NET: Nissan 300ZX forum - Re: Also think about the higher the car is the higher the cheery
Subject
Re: Also think about the higher the car is the higher the cheery
Posted by
Evan(CA)
on July 14, 2014 at 5:50 PM
This message has been viewed
199
times.
In Reply To
Also think about the higher the car is the higher the cheery
posted by induetime
on July 14, 2014 at 12:25 PM
Message
I bought the picker used and I think it's from northern tool. It says big red on it
Follow Ups
The z is prepped and ready for surgery.
-
Evan(CA)
01:44:54 07/13/14
extra things I did while engine out
-
Drk93TT
07:38:22 07/13/14
Agree, and would add:
-
ThisIsSparTTa
08:27:41 07/13/14
Oh yeah
-
Drk93TT
08:37:10 07/13/14
Yeah Knock Sensor can be reached with the engine out
-
BlackholeZ
12:25:19 07/13/14
I'm going to stay with my 555's for as long as they last.
-
Evan(CA)
09:56:27 07/13/14
Just a thought, it is going to cost you twice as much to do
-
HighPsi (NorCal)
10:37:40 07/13/14
I know. Greg has beat this into my head over and over again.
-
Evan(CA)
11:14:48 07/13/14
As long as you re aware, good luck w/ the build,
-
HighPsi (NorCal)
11:39:59 07/13/14
I didn't have anything budgeted for it which is what
-
Evan(CA)
19:24:35 07/13/14
Remove the hood :-)
-
BlackholeZ
12:27:58 07/13/14
I dont think most people remove it
-
ZXoltan
15:05:56 07/13/14
Agreed, I'm still a noob with just 3 pulls, but not needed
-
ThisIsSparTTa
16:54:43 07/13/14
Ive taken it off every time, except this last time...
-
-Grimm-
18:59:33 07/13/14
It does make a lot of room.
-
BlackholeZ
17:18:25 07/13/14
theres a hood prop in the way and it blocks overhead light
-
vorpalZ
19:32:12 07/13/14
never had any reason to want to remove it. (n/m)
-
Antihero
15:09:15 07/13/14
Ya it's about time I wrench on my own car.
-
Evan(CA)
19:13:01 07/13/14
The holes don't have much clearance
-
BlackholeZ
20:20:02 07/13/14
2nd, done this a few times with no issue (n/m)
-
Z-line
10:58:45 07/14/14
Unfortunately his Z is the reason I'm pulling my engine.
-
Evan(CA)
19:09:38 07/15/14
keep in mind the max height of your floor jack before you go
-
LJZTT
13:16:44 07/13/14
~6" piece of 4x4 helps with that... (n/m)
-
BoneZ (MD)
15:05:30 07/13/14
I know but you can only go so high before it's dangerous (n/m)
-
LJZTT
16:47:27 07/13/14
It's scary- I got by with it til I got my low profile
-
BoneZ (MD)
15:05:50 07/14/14
Arcan Costco jack FTW!
-
Evan(CA)
19:27:49 07/13/14
yap, what this doucher says
-
genic
15:42:23 07/14/14
Don't listen to this goat fucker. He only likes 6 ton stands
-
Evan(CA)
16:17:50 07/14/14
uhhhhhh, GGGGGGOOOOOAAAAALLLLLLL!!!!!!!!!! ....??
-
genic
16:28:31 07/14/14
lol...wow (n/m)
-
aliaZ
01:29:19 07/15/14
Also think about the higher the car is the higher the cheery
-
induetime
12:25:40 07/14/14
another important factor (n/m)
-
LJZTT
13:06:41 07/14/14
Re: Also think about the higher the car is the higher the cheery
-
Evan(CA)
16:21:43 07/14/14
even if you extend it out past the 1 ton setting..
-
genic
16:31:29 07/14/14
Re: Also think about the higher the car is the higher the cheery -
Evan(CA)
17:50:13 07/14/14
Post a
Followup
You cannot reply to this message because you are not
logged in
.