Subject	How is your WGs hooked up Tokyo?
Posted by	kickerzx on July 10, 2014 at 7:35 AM
	This message has been viewed 231 times.
In Reply To	I also hit 700 on 1000id, but could not boost more . . . posted by toykoz32 on July 09, 2014 at 03:32 PM
Message	You know with the right configuration you can run as low springpressure as you want but still acheive high boost. Read up on 4 port boostsolenoids and about using 2 3 ports. (It will do the same) Only problem with you going with a 4 port is that they generaly need to be operated with a lower Hz that a 3 port due to heavier piston mass. Around 10Hz vs around 20Hz. Since you run an aftermarket BC that would not be adjustable in your case.
Follow Ups	Guesstimate the e85 whp limit of my fueling setup - 280ZuL8r 19:33:16 07/08/14 ~600whp. The 850cc injectors are your bottleneck. - Evan(CA) 20:06:43 07/08/14 Two years ago. Less than 1000 miles on the setup. - 280ZuL8r 20:33:23 07/08/14 Setup made 493rwhp @ 70% IDC. Kinda makes me 2nd guess (n/m) - 280ZuL8r 21:09:16 07/08/14 Re: Guesstimate the e85 whp limit of my fueling setup - ouikikazz 21:35:39 07/08/14 That's odd..... - 280ZuL8r 22:28:49 07/08/14 I've been running a dual fuel pump setup for awhile - The Devils Z 03:17:33 07/09/14 looks ok to me - JaffaUK 05:59:19 07/09/14 Is your profile current? You did 800rwhp on 850cc injectors? - 280ZuL8r 10:01:14 07/09/14 On 93 that is reasonable, not E85. - zxtuner161 10:21:54 07/09/14 exactly - JaffaUK 11:10:12 07/09/14 yes profile is current and yes 800rwhp and I ran out - The Devils Z 20:44:07 07/09/14 You left out base fuel pressure (n/m) - induetime 00:45:06 07/09/14 Here is what my setup did.... - Madhatter10-6 08:44:46 07/09/14 why did you set you base fp @60? better spray? (n/m) - toykoz32 11:12:59 07/09/14 because..... - Madhatter10-6 15:04:19 07/09/14 Did it take you some time scaling your fuel maps for that? (n/m) - toykoz32 15:33:56 07/09/14 Yes... - Madhatter10-6 08:57:44 07/10/14 good to hear, I asked because id2000 have a better flow - toykoz32 11:46:26 07/10/14 Doing a set-up with dual 485's this fall/winter. - Z ONLY1 10:20:15 07/09/14 If you're worried about the amps drawn, just run the second - MixManMash 15:17:12 07/09/14 ^^^This (n/m) - Madhatter10-6 10:35:53 07/10/14 yup (n/m) - Z ONLY1 21:21:51 07/10/14 Do both your pumps feed into one -6AN line? - -Grimm- 10:26:55 07/09/14 There will be 2 6AN lines, "Y'd" fitted to an 8AN.. - Z ONLY1 12:14:05 07/09/14 This is what I did as well .. (n/m) - The Devils Z 20:45:33 07/09/14 With 1000's I made ~720rwhp maxed out (n/m) - BOOZTD 3 10:42:24 07/09/14 What kind of dyno? (n/m) - Madhatter10-6 15:02:10 07/09/14 Mustang.... (n/m) - BOOZTD 3 19:33:14 07/10/14 I also hit 700 on 1000id, but could not boost more . . . - toykoz32 15:32:22 07/09/14 How is your WGs hooked up Tokyo? - kickerzx 07:35:27 07/10/14 the top port is connected to my ic piping, lower port to bc - toykoz32 11:58:19 07/10/14 I just dug up a picture from the web so that i didnt have - kickerzx 13:10:27 07/10/14 And as i said the same can be aceived using two - kickerzx 13:23:57 07/10/14 A sidenote on that relay. - kickerzx 13:32:09 07/10/14
Post a Followup	You cannot reply to this message because you are not logged in.