Subject	hondabond ht. is the best i have used. (n/m)
Posted by	slayer fan on May 25, 2014 at 11:57 AM
	This message has been viewed 227 times.
In Reply To	Favorite Oil Pan Gasket Sealer? Black or Grey? Other... posted by OverZealous (CT) on May 24, 2014 at 09:44 PM
Message
Follow Ups	Favorite Oil Pan Gasket Sealer? Black or Grey? Other... - OverZealous (CT) 21:44:11 05/24/14 Re: Favorite Oil Pan Gasket Sealer? Black or Grey? Other... - wild_maxx 21:53:26 05/24/14 I've used both and neither leaked. (n/m) - xpwarrior 22:16:41 05/24/14 The right stuff - Madhatter10-6 22:17:48 05/24/14 Re: The right stuff - OverZealous (CT) 22:59:27 05/24/14 2nd, had great luck with Right stuff - Turbodog (CT) 05:50:35 05/25/14 Fast drying time- long enough working time to spread on - ZXoltan 07:38:38 05/25/14 it is fine unless it takes you 30 mins to install an oil pan (n/m) - John (MD) 10:21:27 05/25/14 Thanks. its supposed to be 5-7 minutes. I guess there's more - ZXoltan 11:14:34 05/25/14 Ultra Copper - permatex 81878 (n/m) - ConVerTT 22:40:58 05/24/14 I use grey (n/m) - ztunerz 23:16:47 05/24/14 I used black purely due to the oil resistance AND more - PiotrC70 23:58:20 05/24/14 I used the black. Not sure if any one else has ran into this - Evan_Wright (Ca) 01:58:46 05/25/14 Very helpful! Thanks. (n/m) - OverZealous (CT) 10:07:19 05/25/14 You sure you had everything clean? - BlackholeZ 11:55:08 05/25/14 Super clean. The problem was the rubber seal just didn't - Evan_Wright (Ca) 13:41:44 05/25/14 permatex right stuff (n/m) - John (MD) 10:19:27 05/25/14 I prefer threebond - aliaZ 10:54:48 05/25/14 hondabond ht. is the best i have used. (n/m) - slayer fan 11:57:58 05/25/14 this^^ 3 different engines no issues (n/m) - puddlejumpinzx 12:19:34 05/25/14 My absolute favorite, though expensive, - HighPsi (NorCal) 12:48:55 05/25/14 Hondabond is the best sealant i've used (n/m) - OUTCAZT 13:54:21 05/25/14 That's what I use. (n/m) - zfreak(Dallas) 12:05:59 05/27/14 Going with Black. Final answer. - OverZealous (CT) 14:47:26 05/25/14 Boo. Copper has the same oil resistance and higher temp - ConVerTT 15:57:58 05/25/14 Lol! - OverZealous (CT) 15:54:20 05/26/14 I haven't done most of that either... - ConVerTT 19:00:04 05/26/14 Probably right that there's little difference in the end. (n/m) - ZXoltan 17:00:54 05/25/14
Post a Followup	You cannot reply to this message because you are not logged in.