Subject	2nd, had great luck with Right stuff
Posted by	Turbodog (CT) on May 25, 2014 at 5:50 AM
	This message has been viewed 237 times.
In Reply To	The right stuff posted by Madhatter10-6 on May 24, 2014 at 10:17 PM
Message	Supposedly one of the goals of the product is to be strong so it resists breakaway which obviously is bad for turbos.
Follow Ups	Favorite Oil Pan Gasket Sealer? Black or Grey? Other... - OverZealous (CT) 21:44:11 05/24/14 Re: Favorite Oil Pan Gasket Sealer? Black or Grey? Other... - wild_maxx 21:53:26 05/24/14 I've used both and neither leaked. (n/m) - xpwarrior 22:16:41 05/24/14 The right stuff - Madhatter10-6 22:17:48 05/24/14 Re: The right stuff - OverZealous (CT) 22:59:27 05/24/14 2nd, had great luck with Right stuff - Turbodog (CT) 05:50:35 05/25/14 Fast drying time- long enough working time to spread on - ZXoltan 07:38:38 05/25/14 it is fine unless it takes you 30 mins to install an oil pan (n/m) - John (MD) 10:21:27 05/25/14 Thanks. its supposed to be 5-7 minutes. I guess there's more - ZXoltan 11:14:34 05/25/14 Ultra Copper - permatex 81878 (n/m) - ConVerTT 22:40:58 05/24/14 I use grey (n/m) - ztunerz 23:16:47 05/24/14 I used black purely due to the oil resistance AND more - PiotrC70 23:58:20 05/24/14 I used the black. Not sure if any one else has ran into this - Evan_Wright (Ca) 01:58:46 05/25/14 Very helpful! Thanks. (n/m) - OverZealous (CT) 10:07:19 05/25/14 You sure you had everything clean? - BlackholeZ 11:55:08 05/25/14 Super clean. The problem was the rubber seal just didn't - Evan_Wright (Ca) 13:41:44 05/25/14 permatex right stuff (n/m) - John (MD) 10:19:27 05/25/14 I prefer threebond - aliaZ 10:54:48 05/25/14 hondabond ht. is the best i have used. (n/m) - slayer fan 11:57:58 05/25/14 this^^ 3 different engines no issues (n/m) - puddlejumpinzx 12:19:34 05/25/14 My absolute favorite, though expensive, - HighPsi (NorCal) 12:48:55 05/25/14 Hondabond is the best sealant i've used (n/m) - OUTCAZT 13:54:21 05/25/14 That's what I use. (n/m) - zfreak(Dallas) 12:05:59 05/27/14 Going with Black. Final answer. - OverZealous (CT) 14:47:26 05/25/14 Boo. Copper has the same oil resistance and higher temp - ConVerTT 15:57:58 05/25/14 Lol! - OverZealous (CT) 15:54:20 05/26/14 I haven't done most of that either... - ConVerTT 19:00:04 05/26/14 Probably right that there's little difference in the end. (n/m) - ZXoltan 17:00:54 05/25/14
Post a Followup	You cannot reply to this message because you are not logged in.