TwinTurbo.NET: Nissan 300ZX forum - Re: Favorite Oil Pan Gasket Sealer? Black or Grey? Other...
Subject
Re: Favorite Oil Pan Gasket Sealer? Black or Grey? Other...
Posted by
wild_maxx
on May 24, 2014 at 9:53 PM
This message has been viewed
252
times.
In Reply To
Favorite Oil Pan Gasket Sealer? Black or Grey? Other...
posted by OverZealous (CT)
on May 24, 2014 at 09:44 PM
Message
I used grey on mine. Make sure all surfaces are completely clean and the oil pan is dry. I learned my lesson the hard way.
Follow Ups
Favorite Oil Pan Gasket Sealer? Black or Grey? Other...
-
OverZealous (CT)
21:44:11 05/24/14
Re: Favorite Oil Pan Gasket Sealer? Black or Grey? Other... -
wild_maxx
21:53:26 05/24/14
I've used both and neither leaked. (n/m)
-
xpwarrior
22:16:41 05/24/14
The right stuff
-
Madhatter10-6
22:17:48 05/24/14
Re: The right stuff
-
OverZealous (CT)
22:59:27 05/24/14
2nd, had great luck with Right stuff
-
Turbodog (CT)
05:50:35 05/25/14
Fast drying time- long enough working time to spread on
-
ZXoltan
07:38:38 05/25/14
it is fine unless it takes you 30 mins to install an oil pan (n/m)
-
John (MD)
10:21:27 05/25/14
Thanks. its supposed to be 5-7 minutes. I guess there's more
-
ZXoltan
11:14:34 05/25/14
Ultra Copper - permatex 81878 (n/m)
-
ConVerTT
22:40:58 05/24/14
I use grey (n/m)
-
ztunerz
23:16:47 05/24/14
I used black purely due to the oil resistance AND more
-
PiotrC70
23:58:20 05/24/14
I used the black. Not sure if any one else has ran into this
-
Evan_Wright (Ca)
01:58:46 05/25/14
Very helpful! Thanks. (n/m)
-
OverZealous (CT)
10:07:19 05/25/14
You sure you had everything clean?
-
BlackholeZ
11:55:08 05/25/14
Super clean. The problem was the rubber seal just didn't
-
Evan_Wright (Ca)
13:41:44 05/25/14
permatex right stuff (n/m)
-
John (MD)
10:19:27 05/25/14
I prefer threebond
-
aliaZ
10:54:48 05/25/14
hondabond ht. is the best i have used. (n/m)
-
slayer fan
11:57:58 05/25/14
this^^ 3 different engines no issues (n/m)
-
puddlejumpinzx
12:19:34 05/25/14
My absolute favorite, though expensive,
-
HighPsi (NorCal)
12:48:55 05/25/14
Hondabond is the best sealant i've used (n/m)
-
OUTCAZT
13:54:21 05/25/14
That's what I use. (n/m)
-
zfreak(Dallas)
12:05:59 05/27/14
Going with Black. Final answer.
-
OverZealous (CT)
14:47:26 05/25/14
Boo. Copper has the same oil resistance and higher temp
-
ConVerTT
15:57:58 05/25/14
Lol!
-
OverZealous (CT)
15:54:20 05/26/14
I haven't done most of that either...
-
ConVerTT
19:00:04 05/26/14
Probably right that there's little difference in the end. (n/m)
-
ZXoltan
17:00:54 05/25/14
Post a
Followup
You cannot reply to this message because you are not
logged in
.