Subject	The dividers are supposed to help spool, at least in theory
Posted by	ZXoltan on March 13, 2013 at 2:24 PM
	This message has been viewed 207 times.
In Reply To	I'm not worried about boost creep posted by WhiTTe Z on March 13, 2013 at 01:50 PM
Message	I dont know that there are any comparison dynos out there. I am planning to install GT2560's with the cast-in dividers. The dividers have a gap in them and dont come all the way to the dp flange. Greg D suggested I leave them out.... however I have the same questions as you regarding the spool. I havent heard of any of the 2560's having boost creep issues and I'm not installing larger piping. It seems the larger piping is the culprit, so I'm inclined to grind out the divider and run the full separators, but not totally sold either way. In all likelihood it wont make a difference either way, but I am open to input.
Follow Ups	Consensus on wastegate separators? - WhiTTe Z 12:27:29 03/13/13 I would like to know this also.... (n/m) - nemo1080 (Iowa) 12:56:30 03/13/13 unless your running enough boost to - samsung-Z [Houston] 13:06:11 03/13/13 The pipes are out - WhiTTe Z 13:30:04 03/13/13 Stock turbos, leave them. I can't say I've read any reports - PiotrC70 13:43:34 03/13/13 I'm not worried about boost creep - WhiTTe Z 13:50:20 03/13/13 so you have no complaints with the way the car drives - LJZTT 14:10:18 03/13/13 He's not looking for issues, just possible free gains (n/m) - Red Hawk (CO) 14:15:32 03/13/13 That's where the whole divorced vs super split pipes came in - PiotrC70 15:23:54 03/13/13 agreed, I remember reading that post - Red Hawk (CO) 15:40:30 03/13/13 "whatever is best in terms of spool-up" to me implies that - LJZTT 16:51:09 03/13/13 Well for what it's worth, I'm going from stock pre-cats - WhiTTe Z 21:29:58 03/13/13 ahh, gotcha, it read as if you already installed them - LJZTT 12:18:24 03/14/13 Pepsi Challenge Haha. Good one :) (n/m) - Red Hawk (CO) 10:31:05 03/14/13 Well as you guys know, it's not every day you have - WhiTTe Z 14:26:08 03/13/13 overthinking it dude - LJZTT 16:55:11 03/13/13 Re: overthinking it dude - ryanZ 19:15:03 03/13/13 apples and oranges, you get a C for effort (n/m) - LJZTT 19:54:42 03/13/13 You're right. - WhiTTe Z 21:18:05 03/13/13 we all drive ourselves a little batty sometimes overthinking - LJZTT 12:16:09 03/14/13 Ah men (n/m) - TTZEDHEAD 20:16:38 03/13/13 The dividers are supposed to help spool, at least in theory - ZXoltan 14:24:58 03/13/13 Just send your question to Dupree in an email with a few - 240Z FeO2 14:25:47 03/13/13 Spoke to Greg - WhiTTe Z 21:35:57 03/13/13 Greg's the man. No sense not going straight to the source - 240Z FeO2 21:46:36 03/13/13 Last time I spoke with Seb (a few months ago) he recommended - ForceFedTT (SoCal) 15:40:27 03/13/13 only remove on full breather mods and big turbos - JaffaUK 16:03:47 03/13/13 What he said.... - Hipendicular 21:23:14 03/13/13 Just want to confirm that this is pretty much - WhiTTe Z 21:38:17 03/13/13 I only hearing about this now? I just went big everything - Rogy 23:58:24 03/13/13 See if you have the issue but chances are you will. - PiotrC70 10:02:50 03/14/13 I have heard this as well, I don't believe any one makes the - DarkZide 21:44:12 03/13/13 Primespeed makes them. I believe they are made to order. (n/m) - michaell32 (FL) 09:42:55 03/14/13 I just read a post about this discussion a week or so ago. - Haasz32 12:22:38 03/14/13 I actually think the explanation had to do with how the - Haasz32 09:25:52 03/15/13
Post a Followup	You cannot reply to this message because you are not logged in.