Subject	GT2560R Dyno Chart - Pretty Ridiculous...
Posted by	Ash's Z on March 07, 2013 at 12:07 PM
	This message has been viewed 3717 times.
Message	Something to say about the Garrett GT2560R turbos here: Tyler DuSchane has a TT I built for him back in 2008 and we recently added our 2.5" Planar Turbo Inlet Kit and 2.5" Charge Pipe Kit to the mix, along with Nismo 740cc injectors. This is a fully built setup - Wiseco pistons, JWT 500-series camshafts, mild portwork, MS Manifolds, AshSPEC MASSIVE SMICs, full 3" exhaust. This car just put down 642RWHP and 562RWTQ, making over 300HP/400TQ by 4000RPM, running Dragon 116 RaceFuel, Tuned using our ZEMulator on a DynoJet 248X "BigWheel" Dyno. Absolutely impressive output from such a small turbo. Previously this car was putting down 542RWHP, so figure an added 100HP at the wheels with just inlet pipes and charge pipes being added to the mix. :) And the uncorrected "actual" power to the wheels - nice weather out today here in FL. :) Enthusiasts soon understand each other. --W. Irving. Are you an enthusiast? If you are out to describe the truth, leave elegance to the tailor. Albert Einstein
Follow Ups	GT2560R Dyno Chart - Pretty Ridiculous... - Ash's Z 12:07:35 03/07/13 Very nice. How much boost could you sustain to redline ? (n/m) - ztunerz 12:13:21 03/07/13 It peaked at 27.6psi and by redline it fell to around 24. (n/m) - Ash's Z 12:20:18 03/07/13 Was this done at 100% duty cycle on the ebc? (n/m) - MeatMan - 604Z.ca - 12:33:41 03/07/13 I just did one peaked 26 psi dropped to 22. Stock cams tho (n/m) - ztunerz 12:56:25 03/07/13 What was peak HP/Tq, with breather mods too? 116 Octane? (n/m) - ZXoltan 15:28:51 03/07/13 604, 582 Link >> - ztunerz 17:36:47 03/07/13 Pretty impressive to get 40 ponies just from a cam swap (n/m) - ZXoltan 19:45:04 03/07/13 Re: GT2560R Dyno Chart - Pretty Ridiculous... - WazTTed 12:15:29 03/07/13 Re: Re: GT2560R Dyno Chart - Pretty Ridiculous... - Ash's Z 12:19:36 03/07/13 found charts ( wow finally dusted off this old SN! ) - tyler@boostpro.net 17:42:03 03/07/13 Here is the pumpfuel dyno @ 18psi, 93 octane. - Ash's Z 13:31:38 03/08/13 Nice! What did it do on pump? (n/m) - Jim (Selin Design) 13:32:30 03/07/13 no pump, no care. (n/m) - Adam (NoVA) 15:04:59 03/07/13 2nd. It's nice seeing the big #'s but how many of us - PiotrC70 19:16:01 03/07/13 sad attitude. (n/m) - ztunerz 19:27:01 03/07/13 realistic attitude - Adam (NoVA) 00:46:03 03/08/13 2nd. Much more valuable to me to show pump gas numbers - Mr.Stacy 08:31:59 03/08/13 Since this is very similar to my recent post - spdrmn15 15:18:20 03/07/13 holy hell! - KongZTT GT28RS MD 20:05:26 03/07/13 Awesome peak numbers for the turbo size...... - Greg D. (Specialty-Z) 20:06:01 03/07/13 wow that is some nice low end - aliaZ 21:55:58 03/07/13 gtx gtx gtx :-) (n/m) - Greg D. (Specialty-Z) 23:07:49 03/07/13 what size do you recommend for road course use? (n/m) - aliaZ 07:31:24 03/08/13 gtx2860r (n/m) - Greg D. (Specialty-Z) 12:06:25 03/08/13 We did dial in the cams on the dyno, 641 peak TQ @ 4500 RPM (n/m) - Greg D. (Specialty-Z) 23:05:19 03/07/13 do you have map images, and example dynos for that turbo? (n/m) - genic 21:36:28 03/08/13 Read that these are stock for the SR20DET (S14).. cool (n/m) - LivinTheDream 23:48:52 03/07/13 The stockers have the same size compressor wheel with just - LivinTheDream 00:33:43 03/08/13 Hey Ash from MN, good to see tyler still has his car! (n/m) - 1badz32 (MN) 01:54:53 03/08/13 i want mine to do this..... (n/m) - Dane (Houston) 05:04:33 03/08/13 what wastegates are on the 2560r turbos also - EVLTWINZ 11:30:33 03/08/13 Garrett 1-bar actuators preset to 12psi base. (n/m) - Ash's Z 12:53:00 03/08/13 Great numbers and all but.... - sdhsbaseball 12:27:33 03/08/13 I would like to point something out here: these turbos were - Ash's Z 12:46:21 03/08/13 Don't get me wrong I know for a fact the larger intercooler - sdhsbaseball 16:57:37 03/08/13 I couldn't agree more with you. What really gets me is tha - Ash's Z 17:50:16 03/08/13 Mustang Dyno/Dyno Dynamics = Eddy Current Dynojet = Inertial - sdhsbaseball 20:15:43 03/08/13
Post a Followup	You cannot reply to this message because you are not logged in.