Subject	Dual Wideband?
Posted by	BlackholeZ on September 04, 2012 at 5:40 PM
	This message has been viewed 796 times.
Message	The OCD in me wants to install a wideband sensor in each testpipe because, well, there's 2 testpipes. Am I being stupid? I have an LM-1 and LMA-3 that I would like to integrate, but it only supports a single wideband. I could weld a bung in each pipe and move the sensor occasionally to ensure that both banks are running the same. Or should I just tell my OCD to STFU? -Dan BlackholeZ VTC Solenoid Caps Installation Procedure "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines "You're the Skrillex of Z32s." BradX (UF)
Follow Ups	Dual Wideband? - BlackholeZ 17:40:09 09/04/12 You could move the sensor back and forth, but then - ForceFedTT (SoCal) 18:11:23 09/04/12 Re: I have a dual wide band and dual EGT setup - miloz 01:51:58 09/05/12 How about two sensors? - SactoTodd 18:32:56 09/04/12 Re: How about two sensors? - mpmarino 18:38:05 09/04/12 yes, I have been thinking about that - BlackholeZ 18:44:42 09/04/12 Unless the controllers are wired together - ZXoltan 02:13:21 09/05/12 Sensors don't like being unpowered in exh streams - BlackholeZ 18:42:26 09/04/12 Can you keep them both powered and just switch between - ZXoltan 18:45:54 09/04/12 been thinking about that, see my reply to mpmarino (n/m) - BlackholeZ 20:17:49 09/04/12 that will quickly ruin the sensors (n/m) - aliaZ 20:56:40 09/04/12 Had to be a reason, thanks! (n/m) - SactoTodd 21:55:23 09/04/12 My pleasure, Todd (n/m) - aliaZ 05:53:34 09/05/12 X-pipe Dual Wideband? - mpmarino 19:00:27 09/04/12 I run two LC-1s connected to a single gauge with a toggle - ConVerTT 19:41:02 09/04/12 That is exactly what I have been thinking of doing. (n/m) - Aqualung 22:21:09 09/04/12 I would recommend dual wideband and datalog and not be - The Devils Z 20:09:21 09/04/12 This is just the beginning - BlackholeZ 20:23:22 09/04/12 Do you need an LMA-3? - Dallas DamonZ 16:22:51 09/05/12 2>1 - Alan(MD/NJ) 20:54:58 09/04/12 that is exactly what I do not want - BlackholeZ 01:34:17 09/05/12 This is why my winter mod will be a CARpc - megaDan 08:32:45 09/05/12 You mean... - DVDBURN (MD) 22:42:22 09/04/12 I should see if I can find the stacks of those boxes I have - BlackholeZ 01:36:06 09/05/12 I had the same dilemma when I was about to order widebands - spdrmn15 20:39:03 09/04/12 road racing? ?_? (n/m) - fuzzymonkey 11:47:09 09/05/12 Here - AHos(Chicago) 12:38:40 09/05/12 I have one wideband and a dual EGT gauge - Broke_as_**** 21:25:37 09/04/12 not true -- you will not catch a lean condition quick enough - The Devils Z 13:16:26 09/05/12 How do you figure that? (n/m) - Broke_as_**** 18:04:57 09/05/12 because I have the setup in my Z now and monitor - The Devils Z 18:30:08 09/05/12 Perhaps the disconnect is the defintion of catch - Broke_as_**** 23:30:49 09/05/12 on a similar note, what are the best multifunction gauges? - BlackholeZ 02:01:05 09/05/12 something like this - aliaZ 06:02:34 09/05/12 Very nice... - BlackholeZ 02:01:20 09/06/12 Re: Dual Wideband? - 2+2Twin Turbo 08:38:11 09/05/12 Re: Re: Dual Wideband? - tacozzz 12:49:09 09/05/12
Post a Followup	You cannot reply to this message because you are not logged in.