Subject	I'll be organizing all the parts needed to do the install
Posted by	LitlElvis on July 14, 2012 at 9:42 AM
	This message has been viewed 726 times.
In Reply To	I have been looking forward to seeing this post posted by Pilot.P on July 14, 2012 at 06:40 AM
Message	At this point, if these were to be installed in a used transmission, I'd say a person should expect to replace all the major shaft bearings (six total), seals and gaskets. Depending upon the condition of your 5th gear and it's synchro rings, some of these may need to be replaced too. One difficulty I ran into was that I needed a thicker snap ring than was available from Nissan; I ended up making a shim to take up the clearance, but next time I would probably make a new snap ring out of tool steel.
Follow Ups	PAR Engineering straight-cut, dog-engagement gearset: Part 2 - LitlElvis 16:02:05 07/13/12 nice (n/m) - aliaZ 16:08:50 07/13/12 You're going to carrying PAR products soon? (n/m) - white22sky 16:21:54 07/13/12 If I can figure out a way to deal with the currency exchange - LitlElvis 16:54:58 07/13/12 I'm sure J-shitface is already studying this post. (n/m) - Draker (Eugene, OR) 17:05:17 07/13/12 Im looking at it this way. - white22sky 17:52:45 07/13/12 I can see tranny's blowing up on people already. (n/m) - Draker (Eugene, OR) 18:12:39 07/13/12 Interesting. I could see clutchless shifts - Boosted1 16:25:15 07/13/12 These gears are also available with a semi-helical cut, - LitlElvis 17:04:26 07/13/12 Very cool, I think theres a video somewhere of a Z with - nicky_z32 16:28:50 07/13/12 Comments/ Questions - ZXoltan 16:30:20 07/13/12 Another question....nics in gears? - Obeeone 16:37:03 07/13/12 Those "nicks" are machined into the gears even in old trans - LitlElvis 16:53:19 07/13/12 Answers - LitlElvis 16:51:53 07/13/12 Very nice. - Obeeone 16:31:52 07/13/12 Nice info - RobZ32 16:44:17 07/13/12 Also - RobZ32 16:45:20 07/13/12 2nd (n/m) - MeatMan - 604Z.ca - 19:28:28 07/13/12 Nice! (n/m) - TheTwinZ (Peru) 18:26:34 07/13/12 Good post! - MeatMan - 604Z.ca - 19:28:07 07/13/12 Here's a vid of PPG - dog gears in a 300zx - RoyaltyPerformance 20:24:11 07/13/12 Interesting. Thanks. (n/m) - DVDBURN (MD) 20:54:15 07/13/12 Are these for road racing applications? thx (n/m) - ZonaZ 21:50:31 07/13/12 Use: when you absolutely, positively can't miss a shift - LitlElvis 09:49:19 07/14/12 what's the total $ investment here? (n/m) - Shiers69 22:13:45 07/13/12 The gears cost $4880 AUD, $500 for bearings >>> - LitlElvis 09:52:42 07/14/12 I have been looking forward to seeing this post - Pilot.P 06:40:36 07/14/12 I'll be organizing all the parts needed to do the install - LitlElvis 09:42:19 07/14/12 Great. Thanks for the reply. (n/m) - Pilot.P 19:26:27 07/14/12 I agree with your wife. It's annoyingly loud. - OverZealous (CT) 12:05:28 07/14/12 I'd be interested in learning more about their helical gears - MixManMash 14:33:38 07/14/12 dog gears - BLACK Z 18:53:53 07/14/12 How is your Z coming along? (n/m) - Pilot.P 19:25:17 07/14/12 Re: How is your Z coming along? - BLACK Z 22:49:29 07/14/12 suh-weet (n/m) - Pilot.P 22:57:45 07/14/12
Post a Followup	You cannot reply to this message because you are not logged in.