Subject	You've got mail :-) (n/m)
Posted by	ConVerTT on May 24, 2012 at 9:42 AM
	This message has been viewed 187 times.
In Reply To	NEGATIVE. Do NOT restrict the hose to the IACV - the posted by Ash's Z on May 24, 2012 at 09:38 AM
Message
Follow Ups	Poor sealing Z1 tb's and how they effect idle control... - Evan_Wright (Ca) 21:01:01 05/23/12 Does it surge more when cold, and smooth out when warmed up? - BoneZ (MD) 21:34:16 05/23/12 Tps sits at .38 volts and shows closed tps "on". I can't - Evan_Wright (Ca) 22:02:20 05/23/12 And when the engines cold it does surge pretty - Evan_Wright (Ca) 22:03:34 05/23/12 Unfortunately I swapped out the entire upper plenum which - BoneZ (MD) 22:16:24 05/23/12 Re: And when the engines cold it does surge pretty - WazTTed 15:51:46 05/24/12 You might have to grind a bit of the plastic tab away - Stadsport (PHX) 02:26:08 05/24/12 I've all ready slotted my tps and grinded some plastic away. - Evan_Wright (Ca) 08:03:55 05/24/12 Have you tried to set TPS between 0.4V and 0.5V? - jschrauwen 08:52:36 05/24/12 I can and have had it at around .42 volts but honestly in - Evan_Wright (Ca) 11:01:54 05/24/12 Re: Poor sealing Z1 tb's and how they effect idle control... - MaxxAction 23:00:55 05/23/12 Yes, I sync'd them before dropping the motor in. (n/m) - Evan_Wright (Ca) 23:17:51 05/23/12 Re: Poor sealing Z1 tb's and how they effect idle control... - MaxxAction 23:05:34 05/23/12 Re: Poor sealing Z1 tb's and how they effect idle control... - Stadsport (PHX) 02:22:59 05/24/12 Yes, I've tried going up and down on the percentages and - Evan_Wright (Ca) 07:57:05 05/24/12 Then I agree with you on both points/ideas - Stadsport (PHX) 13:41:46 05/24/12 Yes I have. I actually did it a second time before - Evan_Wright (Ca) 14:13:46 05/24/12 Re: Then I agree with you on both points/ideas - MaxxAction 19:03:32 05/24/12 I have similar issue and believe it to be TB related. - Boosted1 06:11:58 05/24/12 Additionally, my TPS idle voltage is at 0.45 volts - Boosted1 06:15:50 05/24/12 Are you running 2.5" Intake Piping? - jschrauwen 08:57:35 05/24/12 NEGATIVE. Do NOT restrict the hose to the IACV - the - Ash's Z 09:38:52 05/24/12 You've got mail :-) (n/m) - ConVerTT 09:42:15 05/24/12 FALSE!!! It is "pull" not "push" at idle .... - ConVerTT 09:41:29 05/24/12 Re: FALSE!!! It is "pull" not "push" at idle .... - jschrauwen 11:15:01 05/24/12 Do you not realize your advice is not wanted here? - Aqualung 14:57:30 05/24/12 Re: Do you not realize your advice is not wanted here? - ZPHILE 22:16:52 05/24/12 your sig is too long - Adam (NoVA) 12:48:58 05/25/12
Post a Followup	You cannot reply to this message because you are not logged in.