Subject	you want 9-15 lb springs (n/m)
Posted by	aliaZ on May 01, 2012 at 5:36 AM
	This message has been viewed 195 times.
In Reply To	Hmmm... so if I'm running GT-28r turbos and I want 8 psi posted by ZXoltan on April 30, 2012 at 10:13 AM
Message
Follow Ups	More pics and wastegate question. - PiotrC70 22:10:28 04/29/12 yes you can rotate 180* for the wastegates.. - KongZTT GT28RS MD 22:18:15 04/29/12 Thanks. Not sure yet how I want to do my vacuum lines - PiotrC70 22:27:54 04/29/12 Is it easier to access if they are pointed down? - ZXoltan 22:53:55 04/29/12 the driver side.. yes.. - KongZTT GT28RS MD 22:56:39 04/29/12 Cool pics btw.. Looks like its going to be a clean build! - KongZTT GT28RS MD 22:20:49 04/29/12 My friend was thinking about removing that clip and doing as - PiotrC70 22:35:36 04/29/12 yes you absolutely have to sync the two wastegate actuators - KongZTT GT28RS MD 22:47:48 04/29/12 By your above comment, does this mean I wouldn't be able - PiotrC70 23:03:13 04/29/12 I mean target boost as in if you turned the boost controller - KongZTT GT28RS MD 23:23:07 04/29/12 Doesn't make sense to me... - ZXoltan 03:00:41 04/30/12 Yes, set your wastegates to the absolute minimum boost - dogpile 08:04:10 04/30/12 great info thank you! I'll check what psi they're currently - PiotrC70 08:47:37 04/30/12 Also, your actual boost will be 2-3psi less than the wg. - Woody75 (Denver) 09:39:44 04/30/12 Thanks. I was speaking as basically/generally as I could. (n/m) - dogpile 09:48:25 04/30/12 Hmmm... so if I'm running GT-28r turbos and I want 8 psi - ZXoltan 10:13:10 04/30/12 you want 9-15 lb springs (n/m) - aliaZ 05:36:33 05/01/12 I see a few incorrect statements in this thread........ - Greg D. (Specialty-Z) 11:17:48 04/30/12 When running the stainless oil lines, important thing - ZXoltan 22:55:18 04/29/12 Cool, both are far from touching. (n/m) - PiotrC70 23:12:19 04/29/12 I always flip the wastegate. (n/m) - Woody75 (Denver) 09:31:15 04/30/12 "Flip the wastegate"? I guess u mean rotate the actuator? - ZXoltan 09:41:14 04/30/12 I flip them 180 so they are pointing up. (n/m) - Woody75 (Denver) 09:42:42 04/30/12 Do not bind the PS SS oil line - do this: - Bernie (NoVA) 17:59:20 04/30/12 Isnt that running too close to the exhaust housing/ downpipe (n/m) - ZXoltan 18:57:59 04/30/12 No - it doesn't touch and it is now heat wrapped - Bernie (NoVA) 11:57:50 05/01/12 Nice! thanks. (n/m) - ZXoltan 16:31:42 05/01/12 good progress, my tt engine is almost ready for my 'vert (n/m) - vorpalZ 10:22:45 05/01/12 Nice. Be sure to post pics on your progress. (n/m) - PiotrC70 17:45:13 05/01/12
Post a Followup	You cannot reply to this message because you are not logged in.