Subject	So could you feel this?
Posted by	BlackholeZ on June 30, 2011 at 10:54 AM
	This message has been viewed 282 times.
In Reply To	I won 1st place, lucky me. posted by Woody75 (Denver) on June 29, 2011 at 11:06 PM
Message	I understand the graph looks like it does because the ECU is seeing some wild ass RPMs, but could your butt dyno tell anything was up? -Dan "Capitalization is the difference between helping your Uncle Jack off a horse, and helping your uncle jack off a horse." "'she' also likes to swap since I think I am going to need to give her to woody again." - Dvlhntr "full alphabetic boost mode" - ChristopherTheOne "Two oil eating, angry, spinning triangles of death." - turtleboy on rotary engines
Follow Ups	I won 1st place, lucky me. - Woody75 (Denver) 23:06:28 06/29/11 Congratulations, Tim! LOL - ZXoltan 23:12:03 06/29/11 nice save man! (n/m) - Halo TTZ 23:37:51 06/29/11 wow... congrats... I think... (n/m) - rave 23:38:02 06/29/11 What was your boost at for the dyno? Mike is a crazy guy, - 5280Z_nightstalker 02:00:33 06/30/11 15psi. (n/m) - Woody75 (Denver) 07:15:01 06/30/11 NICE that you finally found that. (n/m) - Bernie (NoVA) 02:23:43 06/30/11 was the car driving weird at all? (n/m) - inf 02:29:50 06/30/11 Seemed to drive and run fine. - Woody75 (Denver) 07:19:23 06/30/11 Just in time, good save. (n/m) - SilverZXTT(CO) 06:51:25 06/30/11 Exactly, would have been pissed to find this on dyno day. (n/m) - Woody75 (Denver) 07:20:14 06/30/11 wow, crazy charts (n/m) - ZiNnYc 07:23:36 06/30/11 congrats on fixing that - aliaZ 08:09:40 06/30/11 that chart looks like a roller coaster - RobZ32 10:42:56 06/30/11 Haha great certificate! - Jim (Selin Design) 10:49:21 06/30/11 I would say there are probably more out there than we think. - Woody75 (Denver) 11:32:21 06/30/11 So could you feel this? - BlackholeZ 10:54:30 06/30/11 No and Yes. - Woody75 (Denver) 11:27:53 06/30/11 So, it's important to check timing periodically. - not4resaleZ 10:56:28 06/30/11 I'm afraid I must challenge your award, good sir. - Stadsport (PHX) 14:28:58 06/30/11 Not sure what you are referring to on the surface machining - Woody75 (Denver) 15:37:46 06/30/11 For the CAS bracket to make it straight and aligned. (n/m) - Stadsport (PHX) 16:11:27 06/30/11 Oh, yes. You have to do this. - Woody75 (Denver) 16:40:14 06/30/11 I remember that! (n/m) - Piranha 23:57:04 06/30/11 Re: I won 1st place, lucky me. - MaxxAction 14:42:58 06/30/11 Yep, the link is in my post. - Woody75 (Denver) 15:08:12 06/30/11 Wow, it was on my 10th anniversary, we both win! (n/m) - CoHPhasor 15:25:59 06/30/11 Sweet catch.. (n/m) - samsungz 19:29:54 06/30/11 Great save and hilarious award. Mike is the man! (n/m) - SeedyROM 22:12:09 06/30/11
Post a Followup	You cannot reply to this message because you are not logged in.