Subject	I am with Dane! (n/m)
Posted by	Jc (Houston) on March 31, 2011 at 2:08 AM
	This message has been viewed 231 times.
In Reply To	Check these out. Just made up a set. >>> posted by Ash's Z on March 30, 2011 at 02:52 PM
Message
Follow Ups	AshSPEC Turbo Inlet System >>> IN PRODUCTION <<< - Ash's Z 11:19:20 03/30/11 Im down for the V2, mine will have to be a little different - fst300zx 11:27:18 03/30/11 We have the option with or without recirc ports as well - Ash's Z 11:40:43 03/30/11 awesome thanks (n/m) - fst300zx 09:05:09 03/31/11 Looks excellent Ash, as for ease of installation, even with - BigTDogg (MA) 11:32:07 03/30/11 You will be very pleased with the ease of installation of - Ash's Z 11:46:14 03/30/11 I like the way induetime attaches the mafs to the ends of - not4resaleZ 11:43:46 03/30/11 If you like that you'll love what I'm about to do next. :) - Ash's Z 11:47:28 03/30/11 Thats what I wanted to hear! :) (n/m) - not4resaleZ 11:49:15 03/30/11 Good to hear. Anyone upgrading to these pipes is going to - sfarrah 11:55:56 03/30/11 We made the set you see with the idea of fitting our DOOLZ - Ash's Z 12:01:47 03/30/11 I hope these are the ones that do not require elbows (n/m) - JMartz 13:31:40 03/30/11 Check these out. Just made up a set. >>> - Ash's Z 14:52:14 03/30/11 I need recirculation ports. Less bend in each bend? (n/m) - not4resaleZ 15:03:14 03/30/11 I'll see what I can do on this tomorrow and post back. - Ash's Z 15:12:07 03/30/11 great...... - zdoc 21:33:05 03/30/11 can you angle them so they are up higher in not down block- - Dane (Houston) 15:43:53 03/30/11 2nd (n/m) - aliaZ 17:40:42 03/30/11 Done. Will post pictures in a couple of hours of the new - Ash's Z 15:12:31 03/31/11 Deleted recirculation ports - JMartz 15:44:38 03/30/11 Lookin good! (n/m) - Mr.Stacy 19:27:39 03/30/11 I am with Dane! (n/m) - Jc (Houston) 02:08:33 03/31/11 Now this design i like a lot better. They would work out - fst300zx 09:18:44 03/31/11 I've built a set today that has this layout AND the recirc - Ash's Z 15:03:00 03/31/11 I would for sure be interested in a set with resurc ports - Jc (Houston) 19:31:10 03/31/11 So when will there be a complete kit from filter elbows - Dane (Houston) 11:46:39 03/30/11 Well, we already have the full 2.5" charge pipe kit - Ash's Z 11:52:21 03/30/11 ... and we have the SpecialtyZ tapered discharge pipes - Ash's Z 11:54:27 03/30/11 Re: ... and we have the SpecialtyZ tapered discharge pipes - Dane (Houston) 14:55:49 03/30/11 I don't need it, but I'm very impressed - collegeboy 12:17:33 03/30/11 This is great. When do we get to see dyno improvement - Haasz32 12:18:31 03/30/11 The car in the pictures is strapped to the dyno right now - Ash's Z 12:50:08 03/30/11 How much bigger are the charge pipes than OEM? - ZXoltan 12:55:42 03/30/11 The OEM system's i.d. varies quite wildly. The pipes - Ash's Z 13:21:57 03/30/11 Need more details on the dual maf setup. Also, is 3" not an - Wright (Ca) 13:22:59 03/30/11 I'll put some pipes together before the day's end for - Ash's Z 13:28:30 03/30/11 Very anxious to see the hp gains!!!!!!! - eriksu9 13:49:45 03/30/11 Nice job! - Ashman2k2 16:29:33 03/30/11 bad ass! (n/m) - moxie (SF) 16:39:02 03/30/11 Awesome!! - RobZ32 16:58:14 03/30/11 I agree - Interested in a dual pop piping kit with no elbows - Zbullet 17:28:58 03/30/11 That is a kit I would be inereted in for sure! (n/m) - Jc (Houston) 18:33:47 03/30/11 Very nice. Thank you! (n/m) - Boosted1 20:27:59 03/30/11 Re: AshSPEC Turbo Inlet System >>> IN PRODUCTION <<< - WazTTed 02:15:08 03/31/11 Great Job Ash! Looking good! - sak01 06:46:32 03/31/11
Post a Followup	You cannot reply to this message because you are not logged in.