Subject	Re: ... and we have the SpecialtyZ tapered discharge pipes
Posted by	Dane (Houston) on March 30, 2011 at 2:55 PM
	This message has been viewed 273 times.
In Reply To	... and we have the SpecialtyZ tapered discharge pipes posted by Ash's Z on March 30, 2011 at 11:54 AM
Message	:-) yeah i know you have charge pipes. im just wondering when its available as package deal. the whole shabag.... induction side and charge side with intercoolers and everything Formerly SpecNATT (Houston)
Follow Ups	AshSPEC Turbo Inlet System >>> IN PRODUCTION <<< - Ash's Z 11:19:20 03/30/11 Im down for the V2, mine will have to be a little different - fst300zx 11:27:18 03/30/11 We have the option with or without recirc ports as well - Ash's Z 11:40:43 03/30/11 awesome thanks (n/m) - fst300zx 09:05:09 03/31/11 Looks excellent Ash, as for ease of installation, even with - BigTDogg (MA) 11:32:07 03/30/11 You will be very pleased with the ease of installation of - Ash's Z 11:46:14 03/30/11 I like the way induetime attaches the mafs to the ends of - not4resaleZ 11:43:46 03/30/11 If you like that you'll love what I'm about to do next. :) - Ash's Z 11:47:28 03/30/11 Thats what I wanted to hear! :) (n/m) - not4resaleZ 11:49:15 03/30/11 Good to hear. Anyone upgrading to these pipes is going to - sfarrah 11:55:56 03/30/11 We made the set you see with the idea of fitting our DOOLZ - Ash's Z 12:01:47 03/30/11 I hope these are the ones that do not require elbows (n/m) - JMartz 13:31:40 03/30/11 Check these out. Just made up a set. >>> - Ash's Z 14:52:14 03/30/11 I need recirculation ports. Less bend in each bend? (n/m) - not4resaleZ 15:03:14 03/30/11 I'll see what I can do on this tomorrow and post back. - Ash's Z 15:12:07 03/30/11 great...... - zdoc 21:33:05 03/30/11 can you angle them so they are up higher in not down block- - Dane (Houston) 15:43:53 03/30/11 2nd (n/m) - aliaZ 17:40:42 03/30/11 Done. Will post pictures in a couple of hours of the new - Ash's Z 15:12:31 03/31/11 Deleted recirculation ports - JMartz 15:44:38 03/30/11 Lookin good! (n/m) - Mr.Stacy 19:27:39 03/30/11 I am with Dane! (n/m) - Jc (Houston) 02:08:33 03/31/11 Now this design i like a lot better. They would work out - fst300zx 09:18:44 03/31/11 I've built a set today that has this layout AND the recirc - Ash's Z 15:03:00 03/31/11 I would for sure be interested in a set with resurc ports - Jc (Houston) 19:31:10 03/31/11 So when will there be a complete kit from filter elbows - Dane (Houston) 11:46:39 03/30/11 Well, we already have the full 2.5" charge pipe kit - Ash's Z 11:52:21 03/30/11 ... and we have the SpecialtyZ tapered discharge pipes - Ash's Z 11:54:27 03/30/11 Re: ... and we have the SpecialtyZ tapered discharge pipes - Dane (Houston) 14:55:49 03/30/11 I don't need it, but I'm very impressed - collegeboy 12:17:33 03/30/11 This is great. When do we get to see dyno improvement - Haasz32 12:18:31 03/30/11 The car in the pictures is strapped to the dyno right now - Ash's Z 12:50:08 03/30/11 How much bigger are the charge pipes than OEM? - ZXoltan 12:55:42 03/30/11 The OEM system's i.d. varies quite wildly. The pipes - Ash's Z 13:21:57 03/30/11 Need more details on the dual maf setup. Also, is 3" not an - Wright (Ca) 13:22:59 03/30/11 I'll put some pipes together before the day's end for - Ash's Z 13:28:30 03/30/11 Very anxious to see the hp gains!!!!!!! - eriksu9 13:49:45 03/30/11 Nice job! - Ashman2k2 16:29:33 03/30/11 bad ass! (n/m) - moxie (SF) 16:39:02 03/30/11 Awesome!! - RobZ32 16:58:14 03/30/11 I agree - Interested in a dual pop piping kit with no elbows - Zbullet 17:28:58 03/30/11 That is a kit I would be inereted in for sure! (n/m) - Jc (Houston) 18:33:47 03/30/11 Very nice. Thank you! (n/m) - Boosted1 20:27:59 03/30/11 Re: AshSPEC Turbo Inlet System >>> IN PRODUCTION <<< - WazTTed 02:15:08 03/31/11 Great Job Ash! Looking good! - sak01 06:46:32 03/31/11
Post a Followup	You cannot reply to this message because you are not logged in.