Subject	Can you put a jack under the crank pulley....
Posted by	BOOZTD 3 on March 16, 2011 at 12:18 PM
	This message has been viewed 251 times.
In Reply To	I give up! Time to sell it! posted by rojoloco (San Diego) on March 16, 2011 at 08:27 AM
Message	That will give yourself a little better of an angle to work with in regards to dealing with the trans tunnel, etc
Follow Ups	I give up! Time to sell it! - rojoloco (San Diego) 08:27:44 03/16/11 I spent 4 hrs total looking for a strut tower nut the - Cap927(Boston) 08:36:47 03/16/11 Most of those alignment tools are plastic crap and do not - MixManMash 08:43:49 03/16/11 yep - aliaZ 09:21:45 03/16/11 It can be very frustrating. - jmw23712 08:45:55 03/16/11 Re: I give up! Time to sell it! (n/m) - Huber300zx 09:15:13 03/16/11 The line up tool needs to be able to be pushed in and pulled - Ziceman(East TN) 09:40:27 03/16/11 First time I did a clutch.. I messed with it for HOURS - KongZTT GT28RS MD 09:44:55 03/16/11 Also, a good rule of thumb is to slide - KongZTT GT28RS MD 09:49:23 03/16/11 you will get it, take a break from it. (n/m) - BoneZ 09:57:32 03/16/11 I tried to fill the air conditioner on my Z yesterday and - TheTwinZ (Peru) 10:00:09 03/16/11 unorthodox, but I use the HF transmission jack to get it - LJZTT 10:28:07 03/16/11 That is not the right way to do it.. - KongZTT GT28RS MD 10:30:33 03/16/11 extremely careful, very small increments and kept the gap - LJZTT 10:47:14 03/16/11 cool.. yea I know that you know what ur doing.. - KongZTT GT28RS MD 10:52:30 03/16/11 actually, I'm learning as I go, lol. - LJZTT 11:05:06 03/16/11 I remember watching Ash disassemble a motor back in 06' - KongZTT GT28RS MD 11:10:39 03/16/11 Find some bolts that are the same size as the - Zwin 10:31:19 03/16/11 Stabbing the tranny eh? :/ - KongZTT GT28RS MD 10:40:34 03/16/11 thanks. which wing you talking about? - Zwin 10:59:13 03/16/11 Mission.. - KongZTT GT28RS MD 11:02:53 03/16/11 i bought mine through japan yahoo auctions. - Zwin 11:39:29 03/16/11 Charls@powertrix has the molds for the mission replica - Shiers69 15:37:02 03/16/11 ^^^^^^^^^^^^ This is what you need... seriously (n/m) - spicyZ 15:32:22 03/16/11 Where in Montebello yesterday? (n/m) - toykoz32 17:38:33 03/16/11 Nope, was in Brea. (n/m) - Zwin 18:03:14 03/16/11 The longer of the two timing belt idler pulley studs works - Guapo 18:51:18 03/16/11 indeed (n/m) - aliaZ 10:29:41 03/17/11 KongZTT mentioned the 2 things I htought of: - zellamay 11:36:12 03/16/11 Can you put a jack under the crank pulley.... - BOOZTD 3 12:18:42 03/16/11 Re: Can you put a jack under the crank pulley.... - jaidieray 17:21:23 03/17/11 A little trick I use when installing the clutch is to find - Ash's Z 12:28:37 03/16/11 You posted this info yrs ago, and it's what helped me. - PCVI 13:02:17 03/16/11 Ditto. Helped me get my transmission in the second time. - 300NASeattle 16:14:22 03/16/11 I do the same...wiggle around until the point where the tool - Ashman2k2 18:36:46 03/16/11 I did the same also to get the trans to line up (n/m) - Hawk 20:15:17 03/16/11 Make sure the back of the car is not slightly higher than... - Black95 12:37:01 03/16/11 Re: I give up! Time to sell it! - CmyZ 14:29:06 03/16/11 tilt engine back, turn trans ~20 degrees clockwise. (n/m) - Bernie (NoVA) 16:37:33 03/16/11 ^2nd! (n/m) - CoHPhasor 19:21:54 03/16/11 3rd (n/m) - Piranha 22:52:12 03/16/11 This has helped me A LOT when doing this. - collegeboy 16:56:21 03/16/11 Took me a while too, just be gentle or else - CoHPhasor 17:19:10 03/16/11 Did you think she was just gonna lift up her skirt for ya? - Milo (SATX) 12:02:01 03/17/11
Post a Followup	You cannot reply to this message because you are not logged in.