Subject	I think the runners are fine compared to the bottom
Posted by	xteam300tt on February 20, 2011 at 1:24 PM
	This message has been viewed 435 times.
In Reply To	whatever happened to plenum work posted by MeetMyTwinz on February 19, 2011 at 10:08 PM
Message	portion of the lower plenum , That's your choke point . You can open up the top all you want , it still has to squeeze through the lower plenum . So port match the lower intake to ported heads and take out that restriction . The stock lower intake ports are smaller than the head intake ports to begin with .
Follow Ups	whatever happened to plenum work - MeetMyTwinz 22:08:12 02/19/11 Still being done, must be the sauce. (n/m) - ttz'in (NorCal) 22:59:41 02/19/11 Whats the process or who does this? I am doing a plenum pull - Hoppy2 06:19:54 02/20/11 There are quite a few companies who do this - lazer(NJ) 07:44:11 02/20/11 Not from extrude hone - toykoz32 12:15:09 02/20/11 Re: Whats the process or who does this? I am doing a plenum pull - MeetMyTwinz 07:59:52 02/20/11 extrudehome.com - czh5005 08:22:44 02/20/11 way to go (n/m) - JMartz 11:19:58 02/20/11 What's an extrude home? Is that like a plastic house? - Bernie (NoVA) 11:38:55 02/20/11 spaghetti sauce? (n/m) - MeetMyTwinz 07:57:14 02/20/11 not really. at ~$400, it's near the bottom of the list - nissansx 12:21:09 02/20/11 You mean old-fashioned, home-ported plenums? - LitlElvis 10:35:45 02/20/11 That's awesome (n/m) - outkaZTT 10:44:18 02/20/11 dibs (n/m) - Bernie (NoVA) 11:31:42 02/20/11 You know you want to go custom ;) - Broke_as_**** 11:56:28 02/20/11 Those are unique and cool, but I don't think the stock - LitlElvis 12:08:34 02/20/11 Like you said a few posts down in Ash's thread, - Broke_as_**** 12:15:35 02/20/11 When and why did you go to WI? (n/m) - PiotrC70 12:23:43 02/20/11 January, because the army said go (n/m) - Broke_as_**** 12:44:03 02/20/11 Ahh... that's a good reason.. lol (n/m) - PiotrC70 14:37:47 02/20/11 C-c-c-c-c-c-old - 28° this morning (n/m) - LitlElvis 12:28:19 02/20/11 Pfft, it was -22° a few days ago - Broke_as_**** 12:41:34 02/20/11 To me anything below 40° in western WA feels worse than - LitlElvis 12:50:30 02/20/11 If you can figure out a way to trade I'm in (n/m) - Broke_as_**** 12:53:16 02/20/11 80 degrees in Texas... don't know what all the fuss is about - zfreak(Dallas) 09:39:40 02/21/11 Please, your whole state shut down SB weekend, lol (n/m) - BigTDogg (MA) 08:09:08 02/22/11 What about exrtude honing ? (n/m) - ztunerz 12:30:46 02/20/11 I'm a tight-wad...and the cost to extrude hone was like $295 - LitlElvis 12:37:23 02/20/11 Good thing you can weld ehh ? :) (n/m) - ztunerz 13:21:41 02/20/11 Its double that now. (n/m) - ZiNnYc 23:01:59 02/20/11 Nice! BTW have you read SAE paper 900649? (n/m) - Ashman2k2 14:45:55 02/20/11 I don't believe I have - do you have a copy? (n/m) - LitlElvis 20:54:32 02/20/11 The pdf I have is FileOpen secured.. - Ashman2k2 00:13:53 02/21/11 The the runners seem more than substantial. - T0M 12:28:58 02/20/11 That looks really interesting. - Boosted1 12:50:02 02/20/11 because its longer but retains the same volume increase.. - T0M 13:24:03 02/20/11 have you had these tested? It looks like the back cylinders - 5280Z_nightstalker 13:31:10 02/20/11 The rear is way larger than its stock plenum counterpart - T0M 14:59:53 02/20/11 I think the runners are fine compared to the bottom - xteam300tt 13:24:36 02/20/11 stupid question. how could the plenum be remade lighter? (n/m) - SuparexTT 22:19:10 02/20/11 it's not heavy enough to matter as it is (n/m) - Bernie (NoVA) 23:28:26 02/20/11 Re: whatever happened to plenum work - Carlos Ramirez 08:43:28 02/21/11 bookmarked! (n/m) - blackomega 14:32:31 02/21/11
Post a Followup	You cannot reply to this message because you are not logged in.