Subject	also
Posted by	aliaZ on December 30, 2009 at 8:13 AM
	This message has been viewed 339 times.
In Reply To	hmm posted by aliaZ on December 30, 2009 at 08:09 AM
Message	I've noticed that OEM pistons have oil holes in the bottom of the piston for the pin bores, whereas most forged pistons do not. Perhaps that is a contributing factor?
Follow Ups	Which piston is the best : Ross or CP ? - Dark Diver 16:20:13 12/29/09 read me first! - Seb@Specialty-Z 19:10:49 12/29/09 Re: read me first! - ZXoltan 19:49:41 12/29/09 depends on your definition of "street machine" - aliaZ 22:55:07 12/29/09 Wow, I went with the JE Pistons - ubermiach 21:53:44 12/29/09 Hi Seb, glad to see you back here, in good health I hope :-) - Dark Diver 05:30:37 12/30/09 I personally don't know enough about the CPs - Seb@Specialty-Z 12:39:02 12/30/09 Re: Which piston is the best : Ross or CP ? - Tech@EPR 20:04:33 12/29/09 Piston coatings - ZXoltan 20:10:18 12/29/09 Re: Piston coatings - Tech@EPR 20:14:03 12/29/09 have you had an opportunity to tear down an engine - aliaZ 22:48:37 12/29/09 Re: have you had an opportunity to tear down an engine - Tech@EPR 23:42:11 12/29/09 oh? What are you doing to ensure his crank doesn't break - aliaZ 07:57:39 12/30/09 Re: oh? What are you doing to ensure his crank doesn't break - Tech@EPR 08:24:51 12/30/09 how do you suppose that the hairline crack originated - aliaZ 09:23:21 12/30/09 Re: how do you suppose that the hairline crack originated - Tech@EPR 11:13:14 12/30/09 I still say it was twisting like a wet noodle - canyoncarver 13:02:38 12/30/09 Re: I still say it was twisting like a wet noodle - Tech@EPR 13:06:55 12/30/09 I would agree if the hot spots were all-around - canyoncarver 14:41:54 12/30/09 in what manner did the previous build fail? - aliaZ 17:05:53 12/30/09 Re: in what manner did the previous build fail? - Tech@EPR 10:27:11 12/31/09 do you have any close up pics of the crank fracture? (n/m) - aliaZ 09:24:26 12/30/09 Re: do you have any close up pics of the crank fracture? - Tech@EPR 11:11:22 12/30/09 Beach marks! (n/m) - CaliguyPurdue (Selin Design) 14:23:13 12/30/09 yep (n/m) - aliaZ 15:10:57 12/30/09 interesting - aliaZ 22:52:41 12/29/09 Re: interesting - Tech@EPR 23:39:47 12/29/09 hmm - aliaZ 08:09:34 12/30/09 also - aliaZ 08:13:13 12/30/09 Re: also - Tech@EPR 08:20:41 12/30/09 I'm not talking about the hole under the piston crown - aliaZ 09:26:00 12/30/09 Re: I'm not talking about the hole under the piston crown - Tech@EPR 11:14:05 12/30/09 OEM is not a press fit after the piston - aliaZ 12:14:22 12/30/09 Re: OEM is not a press fit after the piston - Tech@EPR 12:53:58 12/30/09 Re: hmm - Tech@EPR 08:17:48 12/30/09 Re: Re: hmm - aliaZ 10:35:26 12/30/09 Re: Re: Re: hmm - Tech@EPR 11:05:05 12/30/09 FWIW - aliaZ 15:16:38 12/30/09 Re: FWIW - Tech@EPR 00:20:05 12/31/09 whatever - aliaZ 09:31:42 12/31/09 Re: whatever - Tech@EPR 10:31:49 12/31/09 hi - aliaZ 23:10:06 01/01/10 Re: hi - Tech@EPR 18:36:45 01/02/10 where is your shop? - aliaZ 16:51:24 01/04/10 Re: interesting - Tech@EPR 11:30:47 12/30/09 thanks! - aliaZ 12:34:32 12/30/09 Re: thanks! - Tech@EPR 13:04:47 12/30/09 I have CP's, I haven't noticed any noise. (n/m) - RSR 14:33:11 12/30/09 But I've got zoomies, runnin' out the hood. Is that wrong? (n/m) - RSR 10:18:36 12/31/09 Thank you for your detailed response. - Dark Diver 05:56:57 12/30/09 Re: Thank you for your detailed response. - Tech@EPR 08:30:08 12/30/09 Wiseco. - Ash's Z 12:43:32 12/30/09 No other advantage with CP/JE/Ross vs Wiseco ? - Dark Diver 18:33:58 12/30/09
Post a Followup	You cannot reply to this message because you are not logged in.