Subject	Re: have you had an opportunity to tear down an engine
Posted by	Tech@EPR on December 29, 2009 at 11:42 PM
	This message has been viewed 294 times.
In Reply To	have you had an opportunity to tear down an engine posted by aliaZ on December 29, 2009 at 10:48 PM
Message	i'll be tearing down an engine soon enough to check everything to include the bearings and such. The CP pistons I've coated and shown here are going in Steve Melsons engine that I'm building for him. New setup with a lot of different things being done.
Follow Ups	Which piston is the best : Ross or CP ? - Dark Diver 16:20:13 12/29/09 read me first! - Seb@Specialty-Z 19:10:49 12/29/09 Re: read me first! - ZXoltan 19:49:41 12/29/09 depends on your definition of "street machine" - aliaZ 22:55:07 12/29/09 Wow, I went with the JE Pistons - ubermiach 21:53:44 12/29/09 Hi Seb, glad to see you back here, in good health I hope :-) - Dark Diver 05:30:37 12/30/09 I personally don't know enough about the CPs - Seb@Specialty-Z 12:39:02 12/30/09 Re: Which piston is the best : Ross or CP ? - Tech@EPR 20:04:33 12/29/09 Piston coatings - ZXoltan 20:10:18 12/29/09 Re: Piston coatings - Tech@EPR 20:14:03 12/29/09 have you had an opportunity to tear down an engine - aliaZ 22:48:37 12/29/09 Re: have you had an opportunity to tear down an engine - Tech@EPR 23:42:11 12/29/09 oh? What are you doing to ensure his crank doesn't break - aliaZ 07:57:39 12/30/09 Re: oh? What are you doing to ensure his crank doesn't break - Tech@EPR 08:24:51 12/30/09 how do you suppose that the hairline crack originated - aliaZ 09:23:21 12/30/09 Re: how do you suppose that the hairline crack originated - Tech@EPR 11:13:14 12/30/09 I still say it was twisting like a wet noodle - canyoncarver 13:02:38 12/30/09 Re: I still say it was twisting like a wet noodle - Tech@EPR 13:06:55 12/30/09 I would agree if the hot spots were all-around - canyoncarver 14:41:54 12/30/09 in what manner did the previous build fail? - aliaZ 17:05:53 12/30/09 Re: in what manner did the previous build fail? - Tech@EPR 10:27:11 12/31/09 do you have any close up pics of the crank fracture? (n/m) - aliaZ 09:24:26 12/30/09 Re: do you have any close up pics of the crank fracture? - Tech@EPR 11:11:22 12/30/09 Beach marks! (n/m) - CaliguyPurdue (Selin Design) 14:23:13 12/30/09 yep (n/m) - aliaZ 15:10:57 12/30/09 interesting - aliaZ 22:52:41 12/29/09 Re: interesting - Tech@EPR 23:39:47 12/29/09 hmm - aliaZ 08:09:34 12/30/09 also - aliaZ 08:13:13 12/30/09 Re: also - Tech@EPR 08:20:41 12/30/09 I'm not talking about the hole under the piston crown - aliaZ 09:26:00 12/30/09 Re: I'm not talking about the hole under the piston crown - Tech@EPR 11:14:05 12/30/09 OEM is not a press fit after the piston - aliaZ 12:14:22 12/30/09 Re: OEM is not a press fit after the piston - Tech@EPR 12:53:58 12/30/09 Re: hmm - Tech@EPR 08:17:48 12/30/09 Re: Re: hmm - aliaZ 10:35:26 12/30/09 Re: Re: Re: hmm - Tech@EPR 11:05:05 12/30/09 FWIW - aliaZ 15:16:38 12/30/09 Re: FWIW - Tech@EPR 00:20:05 12/31/09 whatever - aliaZ 09:31:42 12/31/09 Re: whatever - Tech@EPR 10:31:49 12/31/09 hi - aliaZ 23:10:06 01/01/10 Re: hi - Tech@EPR 18:36:45 01/02/10 where is your shop? - aliaZ 16:51:24 01/04/10 Re: interesting - Tech@EPR 11:30:47 12/30/09 thanks! - aliaZ 12:34:32 12/30/09 Re: thanks! - Tech@EPR 13:04:47 12/30/09 I have CP's, I haven't noticed any noise. (n/m) - RSR 14:33:11 12/30/09 But I've got zoomies, runnin' out the hood. Is that wrong? (n/m) - RSR 10:18:36 12/31/09 Thank you for your detailed response. - Dark Diver 05:56:57 12/30/09 Re: Thank you for your detailed response. - Tech@EPR 08:30:08 12/30/09 Wiseco. - Ash's Z 12:43:32 12/30/09 No other advantage with CP/JE/Ross vs Wiseco ? - Dark Diver 18:33:58 12/30/09
Post a Followup	You cannot reply to this message because you are not logged in.