Subject	Specialty-Z didn't assemble this engine
Posted by	aliaZ on March 25, 2009 at 12:43 AM
	This message has been viewed 200 times.
In Reply To	Do you ever degree your cams to account for machine posted by AZHeat on March 24, 2009 at 11:34 PM
Message	and therefore did not degree the cams. I believe the engine was assembled by Mattz Garage. I'd say it is pretty clear that they didn't degree the cams either, otherwise they would have caught this mistake.
Follow Ups	Quick update on the 1000 RWHP beast......... - Greg D. (Specialty-Z) 19:56:44 03/24/09 Rdamn...well that's very nice - collegeboy 20:08:43 03/24/09 Heh, nice (n/m) - yobobrox 20:16:32 03/24/09 looking forward to the new numbers (n/m) - komplexZTT 20:20:44 03/24/09 Damn...Looking forward for the next dyno update...GL! (n/m) - TheTwinZ (Peru) 20:22:23 03/24/09 Been there, done that (n/m) - BigTDogg (MA) 20:25:01 03/24/09 The tooth thing, not 1000hp. Like I had to clarify (n/m) - BigTDogg (MA) 20:54:48 03/24/09 LOL. (n/m) - Dave N 23:08:38 03/24/09 hehe (n/m) - RSR 09:19:14 03/25/09 We know you like them with one tooth missing. (n/m) - Scotts94z32 10:58:51 03/25/09 LoL!! (n/m) - Spongerider :) 11:13:11 03/25/09 oh my! (n/m) - RSR 12:48:34 03/25/09 Missing? Try one tooth left, YEE HAW GIT 'R DUN!!! (n/m) - BigTDogg (MA) 14:26:49 03/25/09 Re: Quick update on the 1000 RWHP beast......... - Tech@EPR 20:25:48 03/24/09 One tooth off on the belt is "only" 7.2°... mere childs play - LitlElvis 07:44:30 03/25/09 no vtc's jun cam gears only (n/m) - rated300zx 09:21:37 03/25/09 Re: One tooth off on the belt is "only" 7.2°... mere childs play - Tech@EPR 10:10:31 03/25/09 Re: One tooth off on the belt is "only" 7.2°... mere childs play - AZHeat 10:41:05 03/25/09 Re: Re: One tooth off on the belt is "only" 7.2°... mere childs play - Tech@EPR 17:33:33 03/25/09 Interesting. Kinda makes me nervous about my recent - ZEVAN (Ca) 20:59:28 03/24/09 You would hear it; odds are if the car runs smooth - Machtavian 21:49:11 03/24/09 2nd (n/m) - Piranha(PHX) 22:39:44 03/24/09 WOW! Cheers on the beast! (n/m) - LiL B 21:12:45 03/24/09 Let me guess 1000 whp on turbos only :) (n/m) - ztunerz 21:24:01 03/24/09 Re: Let me guess 1000 whp on turbos only :) - toykoz32 01:20:10 03/25/09 awesome numbers. (n/m) - z32hp*700* 22:14:12 03/24/09 Re: Quick update on the 1000 RWHP beast......... - induetime 22:24:36 03/24/09 One word - NOS (n/m) - ztunerz 09:59:11 03/25/09 that applies when you run boost alone... - Machtavian 18:53:42 03/25/09 There you go again... fixing other shops mistakes LOL - Piranha(PHX) 22:39:18 03/24/09 Do you ever degree your cams to account for machine - AZHeat 23:34:55 03/24/09 who built the motor?? (n/m) - wootwoot 00:19:19 03/25/09 Specialty-Z didn't assemble this engine - aliaZ 00:43:15 03/25/09 Not this engine, but what about engines they built? (n/m) - AZHeat 01:03:01 03/25/09 Can't wait to see the new numbers - jspeckid 01:17:23 03/25/09 Were the cams degreed with the timing belt off a tooth? (n/m) - kuah@splparts.com 07:16:45 03/25/09 The cams were never degreed - aliaZ 09:06:13 03/25/09 Is this an assumption or known fact? - kuah@splparts.com 09:23:33 03/25/09 I never talked/worked with Mattz. Wasn't me :) (n/m) - Woody75 (Denver) 09:52:57 03/25/09 My error (n/m) - kuah@splparts.com 10:28:26 03/25/09 the thought of timing it back into spec could make sense - JustinSCZ32 10:15:27 03/25/09 perhaps I am overly confident - aliaZ 10:50:58 03/25/09 Yes it is possible. The marks on the timing cover - AZHeat 11:29:29 03/25/09 Amazing!! - RobZ32 10:32:01 03/25/09 Would EGT temps indicate this as well? Did this - AZHeat 10:36:21 03/25/09 yes, one on each side, a couple hundred degrees differnce - rated300zx 14:33:54 03/25/09 what are the temps at cruising ? Mine are around - The Devils Z 10:37:29 03/26/09 yes, one on each side, a couple hundred degrees differnce - rated300zx 15:15:11 03/25/09 Timinig belt and marks were all on... - TURBOGAGE(MATTZ Garage) 11:03:23 03/25/09 Nice catch. Looking forward to seeing what it'll do now... (n/m) - TT XTZ 12:35:29 03/25/09
Post a Followup	You cannot reply to this message because you are not logged in.