Subject	Re: Quick update on the 1000 RWHP beast.........
Posted by	Tech@EPR on March 24, 2009 at 8:25 PM
	This message has been viewed 221 times.
In Reply To	Quick update on the 1000 RWHP beast......... posted by Greg D. (Specialty-Z) on March 24, 2009 at 07:56 PM
Message	Were the cams themselves off a few degrees in addition to the belt being off one tooth? I would have thought the engine would have ran a bit rough if it was off by one tooth.
Follow Ups	Quick update on the 1000 RWHP beast......... - Greg D. (Specialty-Z) 19:56:44 03/24/09 Rdamn...well that's very nice - collegeboy 20:08:43 03/24/09 Heh, nice (n/m) - yobobrox 20:16:32 03/24/09 looking forward to the new numbers (n/m) - komplexZTT 20:20:44 03/24/09 Damn...Looking forward for the next dyno update...GL! (n/m) - TheTwinZ (Peru) 20:22:23 03/24/09 Been there, done that (n/m) - BigTDogg (MA) 20:25:01 03/24/09 The tooth thing, not 1000hp. Like I had to clarify (n/m) - BigTDogg (MA) 20:54:48 03/24/09 LOL. (n/m) - Dave N 23:08:38 03/24/09 hehe (n/m) - RSR 09:19:14 03/25/09 We know you like them with one tooth missing. (n/m) - Scotts94z32 10:58:51 03/25/09 LoL!! (n/m) - Spongerider :) 11:13:11 03/25/09 oh my! (n/m) - RSR 12:48:34 03/25/09 Missing? Try one tooth left, YEE HAW GIT 'R DUN!!! (n/m) - BigTDogg (MA) 14:26:49 03/25/09 Re: Quick update on the 1000 RWHP beast......... - Tech@EPR 20:25:48 03/24/09 One tooth off on the belt is "only" 7.2°... mere childs play - LitlElvis 07:44:30 03/25/09 no vtc's jun cam gears only (n/m) - rated300zx 09:21:37 03/25/09 Re: One tooth off on the belt is "only" 7.2°... mere childs play - Tech@EPR 10:10:31 03/25/09 Re: One tooth off on the belt is "only" 7.2°... mere childs play - AZHeat 10:41:05 03/25/09 Re: Re: One tooth off on the belt is "only" 7.2°... mere childs play - Tech@EPR 17:33:33 03/25/09 Interesting. Kinda makes me nervous about my recent - ZEVAN (Ca) 20:59:28 03/24/09 You would hear it; odds are if the car runs smooth - Machtavian 21:49:11 03/24/09 2nd (n/m) - Piranha(PHX) 22:39:44 03/24/09 WOW! Cheers on the beast! (n/m) - LiL B 21:12:45 03/24/09 Let me guess 1000 whp on turbos only :) (n/m) - ztunerz 21:24:01 03/24/09 Re: Let me guess 1000 whp on turbos only :) - toykoz32 01:20:10 03/25/09 awesome numbers. (n/m) - z32hp*700* 22:14:12 03/24/09 Re: Quick update on the 1000 RWHP beast......... - induetime 22:24:36 03/24/09 One word - NOS (n/m) - ztunerz 09:59:11 03/25/09 that applies when you run boost alone... - Machtavian 18:53:42 03/25/09 There you go again... fixing other shops mistakes LOL - Piranha(PHX) 22:39:18 03/24/09 Do you ever degree your cams to account for machine - AZHeat 23:34:55 03/24/09 who built the motor?? (n/m) - wootwoot 00:19:19 03/25/09 Specialty-Z didn't assemble this engine - aliaZ 00:43:15 03/25/09 Not this engine, but what about engines they built? (n/m) - AZHeat 01:03:01 03/25/09 Can't wait to see the new numbers - jspeckid 01:17:23 03/25/09 Were the cams degreed with the timing belt off a tooth? (n/m) - kuah@splparts.com 07:16:45 03/25/09 The cams were never degreed - aliaZ 09:06:13 03/25/09 Is this an assumption or known fact? - kuah@splparts.com 09:23:33 03/25/09 I never talked/worked with Mattz. Wasn't me :) (n/m) - Woody75 (Denver) 09:52:57 03/25/09 My error (n/m) - kuah@splparts.com 10:28:26 03/25/09 the thought of timing it back into spec could make sense - JustinSCZ32 10:15:27 03/25/09 perhaps I am overly confident - aliaZ 10:50:58 03/25/09 Yes it is possible. The marks on the timing cover - AZHeat 11:29:29 03/25/09 Amazing!! - RobZ32 10:32:01 03/25/09 Would EGT temps indicate this as well? Did this - AZHeat 10:36:21 03/25/09 yes, one on each side, a couple hundred degrees differnce - rated300zx 14:33:54 03/25/09 what are the temps at cruising ? Mine are around - The Devils Z 10:37:29 03/26/09 yes, one on each side, a couple hundred degrees differnce - rated300zx 15:15:11 03/25/09 Timinig belt and marks were all on... - TURBOGAGE(MATTZ Garage) 11:03:23 03/25/09 Nice catch. Looking forward to seeing what it'll do now... (n/m) - TT XTZ 12:35:29 03/25/09
Post a Followup	You cannot reply to this message because you are not logged in.