Subject	calculated risk.
Posted by	AntiHero on December 07, 2008 at 2:30 PM
	This message has been viewed 46 times.
In Reply To	It seems surprising that someone who's been here posted by canyoncarver on December 07, 2008 at 09:43 AM
Message	The engine is tired (this engine has outlasted the first two Z's it was in, and is in its third car now) and a built engine is something ive been looking to do. If i could put it back together long enough to run till it gets warm out, great, if not, no biggie. Antihero These 2530's ain't half bad ;)
Follow Ups	engine carnage guestimates... - AntiHero 14:35:08 12/06/08 Explain what you mean by "died." - treese88 14:41:57 12/06/08 lost power. "Stalled and now wont start" - AntiHero 14:46:31 12/06/08 Re: lost power. "Stalled and now wont start" - Seb (specialty-Z) 15:22:43 12/06/08 uhhh? wrong post? (n/m) - AntiHero 15:31:07 12/06/08 just saying it could have overheated. - Seb (specialty-Z) 15:37:32 12/06/08 huh? - AntiHero 15:40:17 12/06/08 maybe overheats till the crank or cams seize? (n/m) - AntiHero 15:42:38 12/06/08 nope (n/m) - Drk93TT 15:51:16 12/06/08 check your CAS connection. (n/m) - nemo1080 (Iowa) 15:45:47 12/06/08 cas is fine - AntiHero 15:47:57 12/06/08 that does suck. good luck man! (n/m) - nemo1080 (Iowa) 23:27:50 12/06/08 clarification... - AntiHero 15:50:00 12/06/08 tensioner failed (n/m) - Guapo 15:51:02 12/06/08 would you bother with a timing belt job? - AntiHero 15:53:04 12/06/08 Get a new tensioner. - ZXRider(SoCal) 16:02:25 12/06/08 Re: Get a new tensioner. - txq45 16:07:41 12/06/08 Third (n/m) - Gordo 93TT Daytona 16:37:46 12/06/08 4th, and don't mess with replacing the radiator to run it. - TriniTT 19:00:17 12/06/08 and/or the center idler pulley stud. (n/m) - zfreak(Dallas) 17:40:17 12/06/08 That wouldn't cause the belt to be loose. (n/m) - TriniTT 18:59:11 12/06/08 yes it would - spyhunterTT(nj) 07:59:49 12/07/08 oh yeah.. :) true. (n/m) - zfreak(Dallas) 09:46:21 12/07/08 120K kit since its unknown age. lmk when you wanna do it. (n/m) - ZiNnYc 01:08:22 12/07/08 a leak down test will tell you if your valves are bent (n/m) - aliaZ 16:46:50 12/06/08 It seems surprising that someone who's been here - canyoncarver 09:43:06 12/07/08 Pull your plenum and look down into your heads to see if a - amp300zx 11:17:27 12/07/08 calculated risk. - AntiHero 14:30:57 12/07/08
Post a Followup	You cannot reply to this message because you are not logged in.