Subject	Ahh!!
Posted by	96300NAZ on September 22, 2008 at 10:27 AM
	This message has been viewed 790 times.
In Reply To	More progress pics. posted by DVDBURN (MD) on September 21, 2008 at 10:44 PM
Message	NICE WORK!!! I do automation for a living involving lots of electrical work. I must say that is an awesome job tieing everything in and making it look "factory". I've seen alot of work where individuals will hack job their wiring not because of inexperience either. Looking at your as-built, am i to understand that you latch your relay AND turn the key to start the vehicle? Just curious if i'm missing why you did it it that way instead of using your ignition switch as your momentary. Was it used so to hide the momentary for security purposes? Also, if you're done with fabrication for your Nitrous switch, Dynatron bumper repair -base shape 3M Automix 5895 plastic repair - a lil softer for easier sanding These products work great. They hold the same properties as most OEM plastics so they arent prone to cracking or warping like other fabbing materials.
Follow Ups	More progress pics. - DVDBURN (MD) 22:44:37 09/21/08 Can i ask you a question? - blacksc 22:55:26 09/21/08 Occupation: Electronics Technician (n/m) - Kenny 23:09:39 09/21/08 Occupation: Electronics Technician (n/m) - zfreak(Dallas) 23:10:44 09/21/08 i feel bad for anyone that owns that car - ricky6991 22:59:24 09/21/08 What? (n/m) - Dustin 23:09:39 09/21/08 I can see how it may look confusing but actually... - DVDBURN (MD) 23:51:12 09/21/08 Ummm... better after he's done than before. - Barry (NJ) 14:03:13 09/22/08 Nice work ! - Drk93TT 23:23:08 09/21/08 You're an artist and wiring is your canvas! Fantastic - 94Z32XTT 00:06:48 09/22/08 Very interesting. Nice work. (n/m) - turtleboy 05:30:26 09/22/08 nice ! (n/m) - The Devils Z 07:20:35 09/22/08 Yipes! (n/m) - Fuzznutz 07:29:20 09/22/08 Lol :) - DVDBURN (MD) 09:59:57 09/22/08 Re: Lol :) - Fuzznutz 06:47:47 09/23/08 I always enjoy your progress posts (n/m) - treese88 07:44:05 09/22/08 Mechanical Fuel Pressure gauge? - BigTDogg (MA) 09:18:12 09/22/08 The steel braided line? It's for the NOS pressure gauge. (n/m) - DVDBURN (MD) 09:58:30 09/22/08 Ah, gotcha - BigTDogg (MA) 10:22:45 09/22/08 Haha! Good point :) (n/m) - DVDBURN (MD) 11:37:55 09/22/08 Ahh!! - 96300NAZ 10:27:27 09/22/08 Thanks. - DVDBURN (MD) 11:55:54 09/22/08 Nice as always.. - eriksu9 10:37:27 09/22/08 Looking nice...you've been busy - kandy2dr(satx) 18:13:33 09/22/08 Nice work - Boosted1 19:44:03 09/22/08 very nice again man! (n/m) - KongZTT GT28RS MD 22:37:40 09/22/08
Post a Followup	You cannot reply to this message because you are not logged in.