Subject	I've only seen one set fail from cracking in the center.
Posted by	Milo (SATX) on August 12, 2008 at 6:20 PM
	This message has been viewed 162 times.
In Reply To	Were'nt Noltec mounts critically failing on alot of cars?? (n/m) posted by Medici (NorCal) on August 12, 2008 at 06:11 PM
Message	This was mainly due to heat causing the material to get stiff and eventually crack over time. I simply just heat wrapped them and installed a set on NA for a bit. Ran with no problem. Looked the same when I pulled them out after 8K miles. But I wouldn't buy them again just for the shear fact of the bad internet mojo that everyone else has had.
Follow Ups	Ebay solid aluminum motor mounts - flabz 17:24:41 08/12/08 I would imagine the vibrations of the engine would make - Waggz 17:30:12 08/12/08 Agreed, I think these would have been a better choice. - 600ZXR 17:43:23 08/12/08 The Ford mounts are even better at about $17 each. (n/m) - Woody75 (Denver) 12:35:31 08/13/08 Can't put domestic parts on my Z. I am not looking to go to - 600ZXR 19:01:01 08/13/08 Thats pretty aggressive for a street car... - Medici (NorCal) 18:05:58 08/12/08 Installed them on a local guys car, he hated them and - Milo (SATX) 18:08:11 08/12/08 Were'nt Noltec mounts critically failing on alot of cars?? (n/m) - Medici (NorCal) 18:11:53 08/12/08 Weren't they melting down? (n/m) - Waggz 18:12:43 08/12/08 I beleive they blew out - Drk93TT 18:18:39 08/12/08 Both as it turns out from searching - Waggz 18:23:45 08/12/08 I've only seen one set fail from cracking in the center. - Milo (SATX) 18:20:24 08/12/08 the noltec mounts are simply a poor design - aliaZ 18:33:33 08/12/08 mine broke - Bret (Generation Z) 01:54:42 08/13/08 Noltecs suck (n/m) - Guapo 18:18:35 08/12/08 Haven't looks out there for a quality replacement in a while - Milo (SATX) 18:21:40 08/12/08 stock (n/m) - Guapo 18:22:40 08/12/08 What ever happened with Turbo Boss's version of a - Milo (SATX) 18:24:37 08/12/08 TB tend to make the motor sit too high. Dunno on any recall - Guapo 18:27:20 08/12/08 Turbo Boss sucks - aliaZ 18:32:04 08/12/08 Anyone ever try the Urethane ones? - BigTDogg (MA) 18:16:35 08/12/08 I have them. Its good (n/m) - Pilot.P (NZ) 18:20:45 08/12/08 No fitment issues? Not too harsh for street driving? (n/m) - BigTDogg (MA) 18:55:18 08/12/08 No and No =] - Pilot.P (NZ) 19:01:47 08/12/08 solid mounts in the front arent the problem in Z32s - Drk93TT 18:19:40 08/12/08 No doubt it will put stress on the chassis - njz 18:26:14 08/12/08 Go OEM - phillyz 18:33:32 08/12/08 I made my own solid mounts after both my noltecs fell apart. - nissanguyz32 19:25:55 08/12/08 2nd. I like them as well. - zcar4me 22:12:10 08/12/08 use nylon lockers or at least a spring washer when - spyhunterTT(nj) 20:00:48 08/12/08
Post a Followup	You cannot reply to this message because you are not logged in.