Subject	Seems a little low for that PSI
Posted by	luke21 on June 14, 2008 at 1:04 PM
	This message has been viewed 88 times.
In Reply To	Dyno results.... posted by spyhunterTT(nj) on June 14, 2008 at 11:57 AM
Message	I made 363rwhp and 390rwtq at 13psi with stock injectors and stock intercoolers. But then again I wasnt as rich as you. My a/f was around 11.8 to 12.0. Lean it out a litte more and you'll make a bit more.
Follow Ups	Dyno results.... - spyhunterTT(nj) 11:57:01 06/14/08 what turbos? (n/m) - Guapo 12:12:44 06/14/08 stock turbos and injectors - spyhunterTT(nj) 12:21:08 06/14/08 Why does your profile say 740's then? Or did I read that - na300zx (OH) 12:26:11 06/14/08 perhaps i need to make it clearer - spyhunterTT(nj) 12:28:45 06/14/08 Gotcha. You sticking with the stock turbos when you - na300zx (OH) 12:30:43 06/14/08 that's the plan for now (n/m) - spyhunterTT(nj) 12:39:30 06/14/08 Cool. That should be fun (n/m) - na300zx (OH) 14:18:51 06/14/08 you ran 20 psi on stock turbos and injectors? (n/m) - Guapo 12:32:08 06/14/08 yes with 100 octane gas - spyhunterTT(nj) 12:41:35 06/14/08 That's because stock turbos start to lose efficency - tdogzjoint 13:03:13 06/14/08 Yall think 20 psi on stock injectors and turbos is alot? - RedTTZ91(OK) 14:16:41 06/14/08 I also told her 1000cc injectors were - RedTTZ91(OK) 14:20:15 06/14/08 Is there even a 1000CC injector that will fit on a Z32? - Waggz 15:26:29 06/14/08 thats Lawton for you.. that place sucked. (n/m) - Halo Z 15:52:29 06/14/08 must be using a special e-bay gauge to show 28 psi (n/m) - ztunerz 16:27:00 06/14/08 aren't you at 100% duty cyle by 15psi on stock injectors? (n/m) - stockplayerz(nyc) 16:29:58 06/14/08 yes - spyhunterTT(nj) 18:07:55 06/14/08 Re: aren't you at 100% duty cyle by 15psi on stock injectors? - Brad@ZSolutions 20:26:54 06/14/08 u got to be kiddin' right ??? ***smakes head *** - The Devils Z 20:50:26 06/14/08 Re: u got to be kiddin' right ??? ***smakes head *** - Brad@ZSolutions 21:02:15 06/14/08 Re: Re: u got to be kiddin' right ??? ***smakes head *** - Brad@ZSolutions 21:06:12 06/14/08 "The stock injectors work fine to 17 PSI if you have enough - not4resaleZ 21:28:53 06/14/08 No, at least not on my car, here is the datalog to prove it - whatsthegoodword 23:11:01 06/14/08 Interesting, Also looks like your fuel and water temp are - not4resaleZ 00:20:59 06/15/08 you are 100 % correct - 14 psi is where it seems to max out (n/m) - ztunerz 02:35:18 06/15/08 What was your A/F ratio? (n/m) - ThunderZ 09:38:58 06/15/08 at 110 oct you can run a lot leaner... (n/m) - ztunerz 02:34:22 06/15/08 no disrespect truly inteneded ..the facts didnt' seem to add (n/m) - The Devils Z 07:20:41 06/15/08 Brad read this >>> - ztunerz 02:32:26 06/15/08 thanks ! (n/m) - The Devils Z 07:21:06 06/15/08 Thanks for the complete and total misinformation. - ni[X]it 07:54:24 06/15/08 To be fair, he didn't say that. - na300zx (OH) 08:06:04 06/15/08 Re: Thanks for the complete and total misinformation. - Brad@ZSolutions 08:38:37 06/15/08 Negative ghost rider. I got this one in the bag. - ni[X]it 08:58:19 06/15/08 This is just constructive criticism, so take it or leave it - na300zx (OH) 09:04:55 06/15/08 Re: This is just constructive criticism, so take it or leave it - Brad@ZSolutions 09:20:48 06/15/08 You're clueless bro. - TriniTT 14:13:21 06/15/08 I don't know the guy or anything about him. - na300zx (OH) 17:00:02 06/15/08 >>> - ztunerz 09:04:28 06/16/08 Lol, you assume I'm talking about complaints posted here. - TriniTT 11:37:30 06/16/08 lol (n/m) - LJZTT 15:21:24 06/15/08 For not being on here much, you are on here an awful lot - na300zx (OH) 16:22:45 06/15/08 Pretty sure he didn't say anything like that. - TriniTT 14:33:48 06/15/08 more like Brad@ZProblems (n/m) - ZiNnYc 13:37:45 06/15/08 I told you man, you can't post here without getting flamed. - TriniTT 14:24:37 06/15/08 Re: I told you man, you can't post here without getting flamed. - Brad@ZSolutions 17:50:17 06/15/08 its really just the way you say things - gt300zxtt 21:34:07 06/15/08 Boom! (n/m) - phillyz 15:34:27 06/14/08 Seems a little low for that PSI - luke21 13:04:02 06/14/08 oops I missed the part where it was on a mustang dyno - luke21 13:06:00 06/14/08 Re: Dyno results.... - movenu 13:49:45 06/14/08
Post a Followup	You cannot reply to this message because you are not logged in.