Subject	That sucks, should have heated them with a torch first (n/m)
Posted by	550HPTT on March 23, 2008 at 9:24 AM
	This message has been viewed 68 times.
In Reply To	Z:1, Me:0 posted by rojoloco (San Diego) on March 22, 2008 at 09:51 PM
Message
Follow Ups	Z:1, Me:0 - rojoloco (San Diego) 21:51:00 03/22/08 PB Blaster..tap a few times, wait a few hours...repeat - Audioquest 22:04:03 03/22/08 We had some PB. It really is amazing stuff. - rojoloco (San Diego) 22:15:28 03/22/08 try Kroil, heard it's even better than PB. (n/m) - inf 22:15:59 03/22/08 Re: Z:1, Me:0 - induetime 22:11:28 03/22/08 you could try'd the stripped bolt sockets - genic 22:26:09 03/22/08 We did try the kit. - rojoloco (San Diego) 23:43:48 03/22/08 Be careful about using stainless on high heat, heat cycle - Myndblur (Daytona) 07:07:26 03/23/08 man that brings back bad memories - Madhatter10-6 23:31:18 03/22/08 Yeah, those studs are tough! - rojoloco (San Diego) 23:44:52 03/22/08 I'm about to install downpipes.... hope I have better luck. (n/m) - Multi_Read 23:56:30 03/22/08 heavy on the PB Blaster the night before. - Spee 18:10:51 03/23/08 Which branch are you in. (n/m) - Sleeper_TTZ(SeKy) 00:01:22 03/23/08 profile check - gt300zxtt 00:08:36 03/23/08 after the pb blaster and tapping - gt300zxtt 00:13:00 03/23/08 PB blaster, soak the bolts overnight - LJZTT 01:25:27 03/23/08 I gave up when the Hobby Shop closed. lol - rojoloco (San Diego) 10:10:10 03/23/08 You DD'ing it? Our shop doesn't charge overnight just during - LJZTT 14:46:14 03/23/08 Just not enough time. - rojoloco (San Diego) 20:02:04 03/23/08 Re: Z:1, Me:0 - Alex_SlicktopTT (WA) 03:06:48 03/23/08 You don't have to remove the precat... - PhantomDragonX 05:46:32 03/23/08 you should have started soaking those bolts days ago (n/m) - 300zx16 07:31:01 03/23/08 Here's a good tip for you... - Spddracer 08:04:47 03/23/08 Redline for trannies = Crap. You didn't miss out on much. (n/m) - ENVYMYZ 09:08:02 03/23/08 False. (n/m) - Waco300zx(DFW) 09:38:48 03/23/08 Try again. (n/m) - ENVYMYZ 17:06:09 03/23/08 You're right, there isn't any positive stories about - Waco300zx(DFW) 18:02:58 03/23/08 90% of the "positive" stories are simply placebo effect. - ENVYMYZ 19:56:47 03/23/08 I would bet your 2nd gear grinid was incurable - Waco300zx(DFW) 07:43:31 03/24/08 That sucks, should have heated them with a torch first (n/m) - 550HPTT 09:24:48 03/23/08 SpecialtyZ is only a couple of hours away... (n/m) - CaliguyPurdue (redesigning) 11:18:49 03/23/08 2nd - ZXRider(SoCal) 11:34:26 03/23/08 You can drop the transmission - ZXRider(SoCal) 11:35:28 03/23/08 did you had OEM pre cats or aftermarket once? (n/m) - DoodMon(SD) 12:40:18 03/23/08 OEM - ZXRider(SoCal) 12:48:26 03/23/08 right...trans always comes out first...THEN the pre-cats. (n/m) - Spee 18:07:47 03/23/08 I was just following the write-up. - rojoloco (San Diego) 20:05:51 03/23/08 I know...that was the first step I skipped :) - Spee 21:44:43 03/23/08 Sounds like a plan. Thanks for the tip too. (n/m) - rojoloco (San Diego) 22:01:50 03/23/08 schedule an appt w\ us since you won't have it done - Seb (specialty-Z) 12:42:55 03/23/08 I'll give you guys a call soon. - rojoloco (San Diego) 20:07:19 03/23/08 Charles can tow it up ;) (n/m) - Seb (specialty-Z) 22:50:36 03/23/08 Best Z mechanic in San Diego: Mark @ 619.249.7870 - Becker 19:54:02 03/23/08 junk the precats for DP's.. - nemo1080 (Iowa) 20:11:24 03/23/08
Post a Followup	You cannot reply to this message because you are not logged in.