Subject	PB Blaster..tap a few times, wait a few hours...repeat
Posted by	Audioquest on March 22, 2008 at 10:04 PM
	This message has been viewed 74 times.
In Reply To	Z:1, Me:0 posted by rojoloco (San Diego) on March 22, 2008 at 09:51 PM
Message	..and then replace precats with good DP's. PB is amazing stuff to free up old nuts 'n bolts. My precats hadn't been off since 1990 and all came off with no issues a couple years ago.
Follow Ups	Z:1, Me:0 - rojoloco (San Diego) 21:51:00 03/22/08 PB Blaster..tap a few times, wait a few hours...repeat - Audioquest 22:04:03 03/22/08 We had some PB. It really is amazing stuff. - rojoloco (San Diego) 22:15:28 03/22/08 try Kroil, heard it's even better than PB. (n/m) - inf 22:15:59 03/22/08 Re: Z:1, Me:0 - induetime 22:11:28 03/22/08 you could try'd the stripped bolt sockets - genic 22:26:09 03/22/08 We did try the kit. - rojoloco (San Diego) 23:43:48 03/22/08 Be careful about using stainless on high heat, heat cycle - Myndblur (Daytona) 07:07:26 03/23/08 man that brings back bad memories - Madhatter10-6 23:31:18 03/22/08 Yeah, those studs are tough! - rojoloco (San Diego) 23:44:52 03/22/08 I'm about to install downpipes.... hope I have better luck. (n/m) - Multi_Read 23:56:30 03/22/08 heavy on the PB Blaster the night before. - Spee 18:10:51 03/23/08 Which branch are you in. (n/m) - Sleeper_TTZ(SeKy) 00:01:22 03/23/08 profile check - gt300zxtt 00:08:36 03/23/08 after the pb blaster and tapping - gt300zxtt 00:13:00 03/23/08 PB blaster, soak the bolts overnight - LJZTT 01:25:27 03/23/08 I gave up when the Hobby Shop closed. lol - rojoloco (San Diego) 10:10:10 03/23/08 You DD'ing it? Our shop doesn't charge overnight just during - LJZTT 14:46:14 03/23/08 Just not enough time. - rojoloco (San Diego) 20:02:04 03/23/08 Re: Z:1, Me:0 - Alex_SlicktopTT (WA) 03:06:48 03/23/08 You don't have to remove the precat... - PhantomDragonX 05:46:32 03/23/08 you should have started soaking those bolts days ago (n/m) - 300zx16 07:31:01 03/23/08 Here's a good tip for you... - Spddracer 08:04:47 03/23/08 Redline for trannies = Crap. You didn't miss out on much. (n/m) - ENVYMYZ 09:08:02 03/23/08 False. (n/m) - Waco300zx(DFW) 09:38:48 03/23/08 Try again. (n/m) - ENVYMYZ 17:06:09 03/23/08 You're right, there isn't any positive stories about - Waco300zx(DFW) 18:02:58 03/23/08 90% of the "positive" stories are simply placebo effect. - ENVYMYZ 19:56:47 03/23/08 I would bet your 2nd gear grinid was incurable - Waco300zx(DFW) 07:43:31 03/24/08 That sucks, should have heated them with a torch first (n/m) - 550HPTT 09:24:48 03/23/08 SpecialtyZ is only a couple of hours away... (n/m) - CaliguyPurdue (redesigning) 11:18:49 03/23/08 2nd - ZXRider(SoCal) 11:34:26 03/23/08 You can drop the transmission - ZXRider(SoCal) 11:35:28 03/23/08 did you had OEM pre cats or aftermarket once? (n/m) - DoodMon(SD) 12:40:18 03/23/08 OEM - ZXRider(SoCal) 12:48:26 03/23/08 right...trans always comes out first...THEN the pre-cats. (n/m) - Spee 18:07:47 03/23/08 I was just following the write-up. - rojoloco (San Diego) 20:05:51 03/23/08 I know...that was the first step I skipped :) - Spee 21:44:43 03/23/08 Sounds like a plan. Thanks for the tip too. (n/m) - rojoloco (San Diego) 22:01:50 03/23/08 schedule an appt w\ us since you won't have it done - Seb (specialty-Z) 12:42:55 03/23/08 I'll give you guys a call soon. - rojoloco (San Diego) 20:07:19 03/23/08 Charles can tow it up ;) (n/m) - Seb (specialty-Z) 22:50:36 03/23/08 Best Z mechanic in San Diego: Mark @ 619.249.7870 - Becker 19:54:02 03/23/08 junk the precats for DP's.. - nemo1080 (Iowa) 20:11:24 03/23/08
Post a Followup	You cannot reply to this message because you are not logged in.