Subject	for mine, i bolted the ECU towards the right side...
Posted by	apudapus on January 15, 2008 at 2:39 AM
	This message has been viewed 342 times.
In Reply To	Harness extensions- I was looking at this so I don't hack posted by ThunderZ on January 14, 2008 at 10:54 PM
Message	of the kick panel. i modified the stock ECU bracket and bolted it at one location on the right. for my new setup, i'm going to make a custom bracket that looks a lot cleaner than that. note: the harness that is connected to the ECU is an OBD2->OBD1 harness. i have (had) a 96 NA wiring harness and a 93 TT ECU. here are pics of the harnesses i've made How it's made OBD1->OBD1 Harness OBD2->OBD1 Harness *********************************
Follow Ups	Harness extensions- I was looking at this so I don't hack - ThunderZ 22:54:56 01/14/08 AFter I wrestled with mine, there was no way I was taking - zgene4 22:59:27 01/14/08 Sounds like it was a tough install. Were you able to at - ThunderZ 23:09:48 01/14/08 Not tough, just not stock. Yes, I was able to fit - zgene4 23:27:42 01/14/08 I just made some brackets and moved it to the other side - Broke_as_**** 02:16:14 01/15/08 dang, that's nice. - apudapus 02:41:22 01/15/08 patent pending mofo!!! - Broke_as_**** 03:22:32 01/15/08 i'm planning on bending some sheet metal to make the bends. - apudapus 11:52:47 01/15/08 Very nice. (n/m) - Bernie (NoVA) 02:56:17 01/15/08 I did the same but just used velcro. (n/m) - Woody75 (Denver) 08:17:10 01/15/08 Where are these harness extensions available for purchase? (n/m) - Barry'z (NJ) 15:10:29 01/15/08 Didn't make the group buy? - Broke_as_**** 15:35:50 01/15/08 Thanks! (n/m) - Barry'z (NJ) 18:38:02 01/15/08 for mine, i bolted the ECU towards the right side... - apudapus 02:39:07 01/15/08 Nice job on the harness conversion - I'll likely need - Bernie (NoVA) 02:58:19 01/15/08 Whoa, just a bit of work in that one eh? (n/m) - Broke_as_**** 03:05:23 01/15/08 Nice job on that wireing! looks like a nice project haha (n/m) - 91300zxttkid 05:51:14 01/15/08 Nice work dude! (n/m) - Turnerscasa (Dallas) 05:57:01 01/15/08 Re: for mine, i bolted the ECU towards the right side... - WazTTed 06:40:30 01/15/08 That's how I did mine too. Nice conversion harness! (n/m) - Dallas DamonZ 07:11:50 01/15/08 nice work, how you know how to do that stuff is beyond me... - Craig300ZX 10:43:56 01/15/08 That harness looks familiar - ZXRider(SoCal) 11:01:22 01/15/08 i just realized that i don't have an extra ECU - apudapus 12:07:05 01/15/08 thanks for the kind words, everyone. - apudapus 12:09:55 01/15/08 Thanks guys, this answered my question. (n/m) - ThunderZ 07:30:13 01/15/08
Post a Followup	You cannot reply to this message because you are not logged in.