Subject	and your motor spins counter clockwise, so you can't
Posted by	boileralum on November 06, 2006 at 11:21 PM
	This message has been viewed 42 times.
In Reply To	Ya problem is posted by ZXRider(SoCal) on November 06, 2006 at 08:36 PM
Message	break it loose that way. I recommend something more sturdy than a screwdriver on the flywheel. Use a prybar that won't be as prone to flexing. Rule #1 - There's always a bastard! JRH(KY): for some reason, when I hear the word 'tranny' I think of transvestite before I do transmission. don't ask me why boileralum: FAGMO! ----------------------------------------- Bill (ImTheDevil): blah blah blah me: Just because you are covered in gasoline right now, doesn't mean you are right! ----------------------------------------- JRH (KY): I'm also using up a weekend this month for Indy and a weekend next month for the USGP. Throw in our trip to PA and GF is getting tired of my car habit. Boy I'm going to miss her :-D
Follow Ups	Finally removed the second cylinder head today.... - WAGGZ 20:08:19 11/06/06 Good job - ZXRider(SoCal) 20:23:41 11/06/06 which bolt are you talking about? damper? (n/m) - SpecNATT (Houston) 20:26:32 11/06/06 Yup - ZXRider(SoCal) 20:27:03 11/06/06 some cars i put a socket with a breaker bar wedged on - SpecNATT (Houston) 20:35:05 11/06/06 Ya problem is - ZXRider(SoCal) 20:36:43 11/06/06 dont need that to crank an engine over ;-) - SpecNATT (Houston) 20:48:49 11/06/06 :slap: (n/m) - zboost(tx) 20:59:34 11/06/06 2nd'd (n/m) - Dave N 21:07:27 11/06/06 :finger: - ZXRider(SoCal) 21:10:30 11/06/06 and your motor spins counter clockwise, so you can't - boileralum 23:21:27 11/06/06 I bought the honda special tool to hold the - ZXRider(SoCal) 02:43:43 11/07/06 What would you do if that didn't work either? :) (n/m) - zboost(tx) 08:13:59 11/07/06 Sawzall... - aggiez32 13:15:08 11/07/06 I'm sure my brother's HK .44 would be sufficient - ZXRider(SoCal) 00:58:02 11/08/06 Hopefully that will do it for you. (n/m) - boileralum 10:24:18 11/07/06 Yes...im praying for it. (n/m) - ZXRider(SoCal) 00:58:22 11/08/06 snap on has a tool to lock the pulley in place - Carp (Show & Go) 09:09:12 11/07/06 my exhaust valves were tan too - SpecNATT (Houston) 20:24:08 11/06/06 nice (n/m) - moxie 20:49:29 11/06/06 tan=good. (n/m) - nemo1080 22:42:44 11/06/06 Re: Finally removed the second cylinder head today.... - Cull1990Red300zx 08:14:10 11/07/06 not too badly, but yes there was some smoke. (n/m) - WAGGZ 13:08:21 11/07/06 >>>> - ztunerz 11:43:32 11/07/06 Naw, the oil only dripped around the outsides of the - WAGGZ 13:13:22 11/07/06
Post a Followup	You cannot reply to this message because you are not logged in.