Subject	Re: Where is Lorca's torque?
Posted by	RegalZ on June 08, 2004 at 11:41 AM
	This message has been viewed 202 times.
In Reply To	Where is Lorca's torque? posted by Woody75 (Denver) on June 08, 2004 at 07:33 AM
Message	I asked the same question because it seems low compared to my dyno in January which was 509/497 at roughly 24 psi. After the intercooler shootout yesterday we raised the boost and did 528/461 at 24.4 psi and 586/519 at 24.4 psi plus N2O SMIC spray (effectively a dry shot). The only two possible differences that I can attribute the lower torque numbers are 1) the ambient air temp was about 40 degrees warmer yesterday than it was in January, or 2) the Gain setting on my SBC-id was not the same. I tend to think its the Gain setting because the entire chart is shifted to the right by about 750 RPM. If the car had not been on the dyno all day we would have done some more pulls with changes to the Gain setting. Get a life Crumpton!
Follow Ups	Intercooler DYNO Shootout: How they rack up->>>> - Ash's Z (In Progress) 20:50:15 06/07/04 Dyno chart is too small. Can't make anything out well. (n/m) - WhiteOutZ 21:02:56 06/07/04 2nd (n/m) - Junxster (NoVA) 21:04:13 06/07/04 Re: 2nd - Russell@Z1 21:11:45 06/07/04 most everyone uses synthetk (n/m) - fourZero 21:15:45 06/07/04 Me too, Ash is just old school. (n/m) - Russell@Z1 21:19:04 06/07/04 clicked on it (n/m) - ZBlacktt 22:58:01 06/07/04 Stock are worse than I thought at those power levels. - SooperZ95 21:03:53 06/07/04 post without the html and crap...post looks like crap - genic 21:06:55 06/07/04 Ash posted and went home, so it can't be fixed. - Russell@Z1 21:15:44 06/07/04 i am in theme 01 ... i will look at it later (n/m) - genic 21:18:23 06/07/04 Very nice! How much will they go for? (n/m) - Slobo7x 21:07:40 06/07/04 Less than the others. - Russell@Z1 21:18:24 06/07/04 Cool, I'll shoot you an email tomorrow. (n/m) - Slobo7x 21:20:49 06/07/04 Awesome. (n/m) - SooperZ95 21:23:46 06/07/04 Why are you so quick to knock the Greddy's, especially when - Z-Jay (Edmonton, AB) 21:28:16 06/07/04 Re: Why are you so quick to knock the Greddy's, especially when - Russell@Z1 21:39:10 06/07/04 Glad my ARC's are on... - Only1Z 21:55:36 06/07/04 So you can read it - EricTTZ 22:05:32 06/07/04 Thanks (n/m) - Russell@Z1 22:06:58 06/07/04 Re: Intercooler DYNO Shootout: How they rack up->>>> - Russell@Z1 23:12:01 06/07/04 I would like to see higher boost shoot out , oh well (n/m) - AzHeat 00:18:55 06/08/04 Something doesn't add up. The Z1 intercooler - AzHeat 00:26:59 06/08/04 Where is Lorca's torque? - Woody75 (Denver) 07:33:38 06/08/04 Re: Where is Lorca's torque? - RegalZ 11:41:25 06/08/04 was this the Bar Plate Monster UAS FMIC? or the tube/fin? (n/m) - Irocsx2002 08:34:46 06/08/04 Just so we know...was the test done with the Front Bumper on - Kyle(Houston) 09:31:35 06/08/04 The bumper was off of the car we tested them on. There - Ash's Z (In Progress) 10:42:07 06/08/04 Stillen are the most efficient SMICs by far. (n/m) - Kenny 14:30:23 06/08/04 The data does not support your claim.. - Ash's Z (In Progress) 14:51:27 06/08/04 I'm afraid it does. - Kenny 15:04:27 06/08/04 Re: Stillen are the most efficient SMICs by far. - Russell@Z1 14:52:03 06/08/04 I'm not arguing hp numbers. - Kenny 15:11:16 06/08/04 Re: I'm not arguing hp numbers. - Russell@Z1 16:12:34 06/08/04 Re: I'm not arguing hp numbers. - RegalZ 00:27:33 06/09/04 I'm sorry you cannot discuss this in a more mature manner. (n/m) - Kenny 23:11:01 06/09/04 LOL, of course you can't address the basis for my opinion - RegalZ 22:51:12 06/10/04 I have nothing against Z1. The numbers just don't add up. - Kenny 23:31:45 06/10/04 Here's the thing ... - RegalZ 00:03:03 06/11/04 Re: Here's the thing ... - Kenny 00:26:48 06/11/04 Try to stay with me this time ... - RegalZ 21:07:35 06/11/04
Post a Followup	You cannot reply to this message because you are not logged in.