EP Racing Internal Coating Services are geared to add performance and protection to the vital engine components. These coatings enable the engine to run with less friction, better lubrication, better combustion, and exhaust flow attributes. One other big improvement is heat retention to keep down engine bay temps.
EP Racing Bearing Coating Services
This form of coating is a dry film lubricant that once applied is baked for 1 hour to chemically bond itself to the substrate.
This dry film lubricant with stands 350,000 psi of pressure. The more abuse (load) that is put on the coating the better its lubricating ability becomes. The coating after it has been applied and set requires NO extra clearances (oil clearances) when going to assembly. The coating wears to a 0 clearance which makes assembly easy. Dark gray in appearance, the coatings color wears off but leaving the physical properties embedded into the sub straight making this coating unlike many others.
- High pressure lubricant.
- Reduces friction, galling and scuffing. Increases part life.
- Requires no clearance changes to compensate for the coating.
- Apply to any part subject to sliding or rotating friction.
- Excellent for use on bearings.
- Water based
There are two options to choose from in this service.
Bearing coating service is $75. This covers both mains and rod bearings. An entire set is coated for this price. You must send me your bearings of choice as this price is only for the coating service.
I also have bearings on the shelf (Clevite & Federal Mogul) that are already coated (full sets) for $200 a set (main/rods). These are the only bearings I use in the engine builds I do. This is a great alternative for those that aren't sure on what bearings to buy or need a set of coated bearings at a moments notice.
Prices are set including shipping!!!
Bearing Service - $75
Coated Bearings Set - $175
__________________________________________
EP Racing Piston Coating Service
The ceramic coating is designed to be used, on any rigid or semi rigid surface experiencing sliding, rotating or oscillating friction, this meaning the piston skirts. It too is designed to carry loads in excess of 350,000 PSI as well as lubricate at temperatures in excess of 1600f. This ceramic coating combines the durability of a ceramic resin with the lubricity of the ceramic lubricant. This coating is also gray in color and acquires a glass like finish in use. This coating has a cured film thickness of ".001" or less and requires no added oil clearance.
Piston Skirt Coating Specs:
* PROTECTIVE TO ABOVE 1600F
Maintains adhesion at base metal temperatures in excess of 1600f.
* HIGHLY RESISTANT TO THERMAL SHOCK
Survives cyclic heating and cooling.
* DURABLE SEMI-RIDGID
Creates a hard, semi rigid, ceramic like finish that survives impact, as well as expansion and contraction without separating from the base metal.
* HIGH LOAD CAPABILITY
Lubricating pigments are capable of carrying loads in excess of 350,000 PSI.
* CORROSION AND CHEMICAL RESISTANT
Resistant to most chemicals and acids while inhibiting oxidation.
The pistons tops (dish) is also coated with a new ceramic after being media blasted to open the substrate surface pores, this makes all the difference and unlike other piston top coating. This coating is baked to ensure the chemical is bonded becoming the sub straight. Many other coatings on the market simply apply the coating and let air cure. This coating once baked is light gray/white in color. Improvements obtained using this coating are listed below.
Piston Top Coating Specs:
- Designed for Performance engines running; Nitrous oxide, Supercharged or Turbocharged.
- Creates a hard surface specifically designed for engines running High volumes of fuel and/or high compression ratios.
- Thermal barrier coating.
- Reduces part temperature. Keeps heat in combustion chamber longer through the power stroke.
- Increase torque and H.P. Increase combustion chamber efficiency.
- Reduce fuel consumption.
- Water based
Piston coating using Ceramic Resin skirt coating w/ piston ceramic tops coated - $200
_______________________________________________
EP Racing Camshaft Coating Service
This coating is a ceramic coating, designed to be used, on any rigid or semi rigid surface experiencing sliding, rotating or oscillating friction. It is designed to carry loads in excess of 350,000 PSI as well as lubricate at temperatures in excess of 1600°F. A unique water based ceramic resin and lubricating solids including, a ceramic lubricating frit. This coating combines the durability of a ceramic resin with the lubricity of the ceramic lubricant. Works well in light duty applications as well as in applications where high temperatures, high loads and high speeds are experienced. When higher temperatures, than most other types of coatings can provide protection at, are experienced, is gray in color and acquires a glass like finish in use. provides a cured film thickness of ".001" or less. Water based material that contains no hazardous solvents.
* PROTECTIVE TO ABOVE 1600°F
- Maintains adhesion at base metal temperatures in excess of 1600°f.
* HIGHLY RESISTANT TO THERMAL SHOCK
- Survives cyclic heating and cooling.
* DURABLE SEMI-RIDGID
- Creates a hard, semi rigid, ceramic like finish that survives impact, as well as expansion and contraction without separating from the base metal.
* HIGH LOAD CAPABILITY
- Lubricating pigments are capable of carrying loads in excess of 350,000 PSI.
* CORROSION AND CHEMICAL RESISTANT
- Resistant to most chemicals and acids while inhibiting oxidation.
Pricing: Full set of camshafts (4) - $175
_______________________________________________
EP Racing Combustion Chamber Coating Service
This service uses the same ceramic resin coating that is used on the piston tops. Coating the chambers and piston tops creates the best efficiency in the combustion cycle as well as keeps the heat throughout the exhaust cycle ensuring you use every bit of heat/exhaust gas to your advantage. This service also coats the valves for free! Get your combustion chambers and valves coated for one low price. This coating once baked is light gray/white in color just like the piston tops. This service requires you to send me your cylinder heads thoroughly cleaned. If cleaning is required additional fees are implied.
Combustion Chamber Coating Specs:
- Designed for Performance engines running; Nitrous oxide, Supercharged or Turbocharged.
- Creates a hard surface specifically designed for engines running High volumes of fuel and/or high compression ratios.
- Thermal barrier coating.
- Reduces part temperature. Keeps heat in combustion chamber longer through the power stroke.
- Increase torque and H.P. Increase combustion chamber efficiency.
- Reduce fuel consumption.
- Water based
Pricing
Combustion chamber coatings w/ valve faces included - $200.
***Note*** You pay shipping both ways
______________________________
EP Racing Exhaust Port Coating Service
This coating is used to isolate heat in the exhaust port and not allow it to radiate into the cylinder head. This improvement keeps your exhaust gas velocity up and your turbo system spooling faster and more efficiently. Black in color with a glass finish, this coating will NEVER come off. When you are ready to clean your exhaust ports out after tearing them down or just want to clean the carbon out for the sake of cleaning, all that is required is to wet a paper towel with any degrease agent and wipe clean. THATS IT!! This chemical coating has an ever lasting bond to the sub straight after its been applied and baked in the oven. Specifically designed for turbocharger/NOS/Supercharged/High Compression engines where heat is in excess.
Exhaust Port Coating Specs:
- Modified Polymer.
- Excellent thermal barrier for exhaust ports.
- Smooth finish enhances flow in exhaust ports.
Pricing
Exhaust Port Coating - $200
______________________________
EP Racing Thermal Dispersant Coating Services
Avid race teams and racers alike look for the advantage in keeping their engines running cleaner and cooler all the time. One of the methods of cooling parts on the engine and reducing engine temps is to apply a thermal dispersant to critical parts. By doing this you...
* Rapidly disperses heat away from a coated component.
* More evenly distributes heat over a coated surface.
* Aids in cooling heat sensitive parts.
Overall enabling the engine to run cooler is what we are all after and in doing so increases efficiency.
Thermal dispersant coating specs:
* Excellent for intake manifolds, brake components, oilpans, turbocharger compressor housings, intercoolers, piping, throttle bodies, etc etc.
* Very good chemical and corrosion resistance.
* Black in color.
* Cosmetically appealing.
Pricing
Thermal Dispersant Coating service - $185
_________________________________________
EP Racing Coated Crankshaft Service
There are two primary reasons for coating a crankshaft:
- Coatings provide increased lubrication to the journals
- Coatings aid in shedding oil from the counter weights. Depending on the intended use there will be a different coating applied due to oil shed capability and thermal properties the coating aids in.
The crankshaft rod journals are coated a ceramic dry film lubricant which cures to a thinner film than most other dry film lubricants. Once the coating has been applied and cured, a burnishing process is conducted. This does two things, removes high peaks in the spraying process and polishes the coating film to ensure the even layer is smooth and ready for assembly. Coating the journals with this dry film coating you will increase lubrication, reduce friction and add a protective layer to the crankshaft. The rotational action of a crankshaft coupled with the pressure fed oiling system, aids in keeping a film of oil in place under pressure. However, when pressures exceed what the oil can carry, the oil will flow away from the point of contact, this is where the coating steps in. The dry film lubricant used can lubricate in pressures exceeding 350,000psi, which is well beyond what you would ever see in use. Another important function of the dry film lubricant is that it is oil retaining and helps keep oil in place.
No additional machining or clearance is needed as this coating burnishes down to a zero clearance factor. I suggest though that you always check your oil clearances for documented purposes as well as to know what your engines clearance is at with any build being conducted.
Coating the counter weights will be done with a thermal dispersant coating which also has an exceptional oil shedding capability to it. Depending on the intended use of the engine a different thermal coating will be used that will be best suited for the work the engine will be doing/seeing.
Overall, this service increases the lubrication level inside the engine and reduces friction. A win/win situation for any avid racer/race team.
***NOTE*** - Customer MUST clean the crankshaft upon receiving. Foreign debris that may lodge itself inside the crankshaft during shipping which will need to be cleaned thoroughly prior to going to assembly. DO NOT polish this crankshaft...EVER!!! That is ever needed from this day forward is to clean the crankshaft well before assembly. As always measure your journals when building and inspecting to ensure the crank is within specifications.
Pricing
Coated Crankshaft Service $300
________________________________________
EP Racing Exhaust Manifold Coating Service
We all know that retaining heat in the manifold leading into the turbocharger will make the turbo spool faster and keep the turbo spooled better between shifts. Applying a thermal barrier like an exhaust manifold coating does an exceptional job at doing this.
EP Racing does a two part coating process to all its exhaust manifold coating jobs. A high ceramic base coat which has exceptional thermal retention properties then a second layer which improves temperature retention to above 2000 degrees F. This combo makes for the best possible solution to aiding in heat retention.
Key things that the coatings do besides retain heat are:
- Great resistance to corrosion. The manifold will last longer with eliminating rust and other corrosion to occur.
- Reduce surface temperature of the manifold. This will equate to reduced under the hood/engine compartment temperatures as well. Reducing this heat will reduce heat in other components like A/C compressors, alternators, power steering pumps, etc etc.
- These coatings that are applied have better flexing/expanding properties than other coatings on the market.
- Black in color
- Cosmetically appealing
This service can be done to any form of cast/steel exhaust product. Downpipes/turbine housings/manifolds/wastegate tubes, etc etc.
Pricing
EP Racing Exhaust Manifold Coating Service - $200
***NOTE*** - Every manifold set that gets coated also gets drilled and tapped for EGT Probes. This is done FREE of charge!!!!!
Im digging deeper into the realm of what can be coated on engine assemblies and I'm continuously finding what areas of certain parts can benefit from a particular coating. Recently I've dove into smaller internal parts like valve springs, retainers, valves, lifters (solid) and other small sub assembly parts that could benefit from a coating regiment.
I now offer coating services for valve stems and wrist pins (full floating design). I've seen several engines after been torn down for inspection for both cores and customers engine sent in to be rebuilt, that there are severe galling issues and binding going on inside the engine. Obviously correct clearances make or break an engine and when you add coatings to the equation things are just that much better!
Coating after market wrist pins & Intake valve stems on your factory/aftermarket valves serves a few purposes.
1. Provides a better lubricated surface
2. Protects area of wear under greater stress/friction
3. Retains oil at the coated area ensuring the part never sees any added friction.
3. Keeps parts running cooler
All these small improvements with coatings can equate to an engine that will run better, smoother, and perform above and beyond what your assembly will run without coatings. Its a win/win situation for the engine to run coated parts. We all know that keeping friction down to a minimum is key and incorporating coatings aids in achieving that result.
Pricing for coating valves runs $100
Pricing for coating wrist pins - $100
Dry film lubricant on the valve stems to aid in lubrication and prevent galling. The valve stems feel like silk once cured and burnished.
Now offering a new coating service to update your forged/stock rods in having them coated. This service has two functions,
1. Oil shedding - this ensures that no parasitic drag/draw can be adhered to the rotating assembly (connecting rods) while in a dynamic state. Enabling the surface to be 100% resistant to oil saturation, this detail keeps the rotating assembly working easier.
2. Thermal barrier - this allows the heat in the connecting rod to be shielded from engine oil and carried away faster and better than if the item was not coated. Having the oil stick to the part and retain heat around it ultimately creates harder working parts due to the fact that oil is saturating the area and maintaining its heat to the part. The thermal dispersant helps in shedding this heat more rapidly and evenly.
This service to upgrade your connecting rods is $250 (this covers pin fitting the pin bore of the rod as well (this feature has not been done yet to the images above) for the set. All work is done in house by me personally. I guarantee my work to be 100%. If you have any questions please email me at my address above.
All coatings are applied by me personally in house. No out sourcing of any kind is done. Parts are guaranteed after coating to function as advertised. Instructions on final assembly are included with each part to ensure they are prepped accordingly before installed. Quick turn around and unbeatable service.
Send me your brand new or used turbos and I will tear them all down...clean them thoroughly then coat them with a thermal barrier coating and thermal dispersant coatings. Together making your turbocharger look stealthy, very eye catching and function better than out of the box.
EP Racing Onyx Series Turbocharger Service is available NOW!
Service includes a full tear down as mentioned above. All housings are three stage cleaned. Media blasted then have the selected coatings applied. Going this route gives the consumer every possible advantage in increasing their performance out of their turbocharger unit. Retaining heat where its most important and dissipating heat where its crucial for lower temps through the intake tract.
All coatings are applied in house and no out sourcing is done of any kind. Quick turn around and quality service!
Turbochargers come back to you fully assembled and ready to be installed on your engine. All turbos after under going this treatment are tagged and serialized.
How to order:
I accept money order or paypal for payment. Please contact me by email or phone to setup arrangements for this service to be done.
Pricing is $150ea turbocharger.
Please contact me for any questions you may have.
Thank you for looking
EP Racing Produce Services - 
