I am parting out my project car that I will not be able to finish. All prices on the performance parts are firm, all other parts are as they say + shipping and Pay Pal will be the payment method + 3%. Please email me with all of your questions at CJM300ZXTT@sbcglobal.net . I have pictures of every part listed and I can take more if need be. Race built Short block - $3,000+ shipping A 1991 TT block and crank were used (crank mic checked perfectly) 89mm CP pistons with heat resistant coating on top and friction reducing coating on skirts Pauter Rods OEM bearings with Swain Tech Molly coating (Clearances were checked using bearing mic.) Crank balanced to within a 10th of a gram ARP main studs installed ARP head studs installed Honed using torque plate Bored on 4-axis CNC NA oil squirters installed Block re-decked and de-burred New Block deck oil restrictors New block oil pugs New freeze plugs Hot tanked many times Rebuilt Short block - $1,500 + shipping The block that was used is NA with the crank that has 147,xxx miles on it as well as the rods. 88mm Weisco pistons stock rods with ARP bolts ( reconditioned, cut the caps and honed to spec) ARP Main studs Balanced crank to within 1 gram OEM Nissan bearings with Swain Tech coating Crank checked for wear (non at all, checked with a .0000" mic) Oil clearances checked ( all within the factory specs, used a bearing mic to check specs) Honed using a Torque Bored on a 4-axis CNC machine Block re decked and de-burred New oil galley plugs and block oil jets NA oil squirters Block was hot tanked multi times File fit top rings I have documented the whole rebuild but if you have and other questions fell free to ask 1990 300zx Chassis in platinum mist metallic - $1,000 obo The chassis has 147,xxx miles on it and began life as a NA automatic. I will be keeping the NA diff. for my 240sx but the rest of the sub frame is there. The body and paint is in good condition with the acceptation of 2 small patches of rust on each rocker panel. Interior is in great condition but of course there is a hole in the drivers seat. Comes with alpine head unit and speakers. 30P NA heads - $150 + shipping Seats have been cut with a 3 angle radius cut Bowl has been blended for the new cut Slightly ported Spark plug boss removed Hot tanked and cleaned Needs to be resurfaced All cam caps are numbered and intact
300zx Performance parts Tomei solid lifters and test shims - $425 Ferrea Valve train (1mm over valves, dual springs, retainers, spring seat locators) - $1300 SPL Parts Fender brace- $225 NEW OEM 90 - 93 engine harness - $320 NEW OEM turbo oil pump - $160 NEW OEM VTC solenoids rh/lh - $260 OEM 300zx parts 1990 na auto Exhaust mid section with cats - $5 Headers with good O2's - make offer Radiator (auto, nearly new with less than 20,000 miles on it) - $100 Timing belt cover (front cover and rear shields)- $30 Condenser AUX fan - make offer Flex plate and trans shield - make offer Cooling Fan with good clutch - $40 Exhaust cam gears (2 sets) - make offer VTC gears (still work fine, no noises) - $90 CAS sensor - $30 CAS sensor with bracket - $50 Ignitor chip - $20 VTC solenoids (2 sets) - $30 a set Coil packs ( I have 10 of them) - $10 each Power steering pump - $100 Water pump pulley - make offer Throttle bodies with linkage - $75 Oil tree - make offer Spark plug galley covers (2 sets) - $20 a set Harmonic balancer - $40 Engine water pipes (various pipes) - make offer Rear ABS sensors - $30 Cruise control - make offer Rear suspension arms (Traction arm and camber arm) - make offer Balance tube - $50 Lower water pipe (font of engine) - make offer Rear Brake calipers - $ 75 OEM 300zx TT 1991 5spd Turbos with manifolds ( good for rebuild or cores) - $300 obo Exhaust manifold heat shields - $80 Oil Pan (in ok condition) - $75 Lower plenum - $50 Upper plenum ( with throttle bodies, linkage, TPS, and idle air controls) - $150 Valve covers - $50 Turbo injectors in rail - $200 Pistons and rods (in good condition) - $100 Intake pipes (bolts to the turbo) - $50
240sx KA24DE parts - Make offers for pricing Intake manifold (idle air accessories still attached) Valve cover Cooling fan with clutch Flywheel (needs resurfacing) MAF sensor Throttle body with TPS Power steering pump Harmonic balancer Coil Water pump pulley Oil Pickup Water pipe Rear mail seal housing 95 240sx Suspension arms with OEM bushings pressed out(includes ES bushings) SR20DET redtop parts - Make offers for pricing Exhaust manifold Crank (spun a rod bearing) Cooling fan with clutch Rods Flywheel (needs resurfacing) 1995 240sx SE wheels - $200 5-lug 5-spoke Have been bead blasted for paint or powder coating Zero curb rash and the wheels are straight
|