Original buyer backed out.. he could not come up with the money..
I am selling because I am going with a much larger (laggier) turbo, I have nitrous to combat the lag of the GT2871-1R turbos I am looking at getting. Here are the specs of this turbo.. -Garrett GT-28R w/ HKS adjustable wastegate actuators (custom brackets)
Dual Ball Bearing
60mm, 60-trim Compressor Wheel
.60 A/R TB25 Compressor Housing
62-trim T25 Turbine Wheel
.64 A/R T25 Turbine Housing These turbos have HKS actuators installed and the pre-load set @ 17psi (both are synchronized equally), which gives ~15psi of base boost. These turbos basically have NO LAG, I would say with great confidence that these turbos with a down pipe and test pipe combination would outspool a STOCK turbo'ed Z with all cats intact. Even when you shut the car off, you can still hear the turbos spooling down, they spin super freely. I have less than 100 miles on these turbos, I intalled them, Drove the car to test everything out, (never even put my front bumper back on), drove it a few more times.. bought cams, lifters, valve springs and decided that now would be a good time to do my full engine build with forged pistons, rods etc since I will be taking the heads off. These turbos have only seen 15psi, I never even turned the boost up and only used Royal purple 10w-30 synthetic racing oil. Tyler @ boostpro.net made 512hp/517tq @ 22psi, @ the rear wheels with the GT28R. With the turbos, I am including, These will be a bolt on application... -Oil Drain fittings that must be used to clear compressor housing from ATPturbo.com -Oil feed lines w/ new crush washers -Compressor inlet flanges, so that you do not need to worry about welding or cutting your Inlet pipes. This adapter allows you to bolt it right up to your factory piping. -Modified motor mount brackets -Modified Oil filter tree housing. -TWO, both passenger and driver side motor mount brackets with mods done to clear the HKS wastegate actuators. -TWO Chrome compressor outlet flanges, alredy cut to fit the GT28R turbos. I am including these pipes with HKS silicone couplers as well.. This is TRULY and full BOLT ON AFFAIR! I could not make this install ANY easier. Here are the Chrome Outlet pipes that I am including
Here are the Chrome Outlet pipes that I am including
Both Turbos are already clocked in proper orientation for the Z, locktite'ed bolts, SS studs, washers, nuts for the down pipes. Still have Garrett 1year Factory warranty ~August. $2100 for these turbos with all things necessary to install. (pipes, brackets, wastegate actuators etc.) Ask other members about me.. I will not rip you off etc.. Serious offers only, Please do not waste my time or yours... AIM me @ Shawn300zxTT , email or call 443-350-3130. Thanks!
-Apexi AVC-R.
I have a BRAND SPANKING NEW AVCR boost controller for sale.
I got one, then got another as a gift. She did not know that I had already purchased one. So one Must go. This is brand new, I have not even taken it out of the package. All hardware included, papers, instructions, etc etc. Very nice boost controller.
-I will take $415 shipped to your door.
-Apexi EL mechanical 60mm boost gauge, Black face. Brand new, never installed. (went with Defi BF gauges and control unit2)
-$100+ shipping , which should only be around $8.
-HKS Super Mega-Flow intake, Works both on TT/NA. Great shape, just replaced filter ~8k miles ago, comes with bracket to keep it from sagging and to keep it away from water, above splash shield, and it has the MAS adapter.
-$140 shipped to your door. Selling because I upgraded to the 4.5" 3-row Greddy FMIC. And wanted to go the Dual MAS, Dual intake set-up. -GReddy Dual filter intake (fits behind a FMIC, uses single MAS sensor) BRAND NEW!!! Highly polished with GReddy Embossed w/ raised letters. Would be a nice upgrade for you TT's or NA's wanting a beautiful, polished single MAS GReddy w/dual chrome 'fenced' filters. Selling because I fabricated my own Dual MAS sensor set-up, I have larger than stock turbos, so I needed more flow.
$215 shipped to your door. -Kuhmo Escta Tires.
255/45/17. They are brand new. Have less than ~10 miles on them. They came with a package wheel/tire deal and I drove it to the tire shop and got them taken off and replaced with lower profile Yoko AVS ES100's 245/40/17's. If you have some MT ET-streets or the MT ET-Drags in 26x10.5x16". I will trade for those Drag tires.
-I will let these go for $220 shipped to your door. -Stock Fuel Pressure Regulator (BRAND NEW, NEVER USED)
Upgraded to Aeromotive Adjustable FPR w/ SS lines.
-$65 shipped -Stock Fuel Dampner (BRAND NEW, NEVER USED)
No need for fuel dampner on Border 850cc injectors that I am using.
-$65 shipped --------OR BOTH BRAND NEW STOCK fpr AND dampner for,
$120 shipped to your door. I will even include about 2-3' of 5/16" high pressure, fuel injection fuel line. Brand NEW, never used. -Stock Fuel hard lines (goes across plenum, next to Balance tube)
-$25 shipped to your door
-Stock TT intercoolers, with the rubber pipes that connect to them, Brackets and Air ducts. GREAT SHAPE, No dents or anything. I upgraded to an GReddy 3-Row FMIC. I have no need for the Stock SMIC's anymore.
-$230 shipped to your door.
-Twinturbo Compressor OUTLET pipes (comes from the outlet on the turbo compressor, I have both Driver and passenger pipes. Great if you are doing the low speed drivability hose, instead of tapping into the stock recuirculation valve(next to the BOV's, just use the DRIVER SIDE compressor outlet pipe on the passenger side turbo and run the 5/8" hose to a "T" fitting @ the AAI valve. No, drilling,cutting,tapping would be required and the low speed driveability hose will be MUCH shorter and cleaner. Email me for more detailed instructions.
-$60 shipped to your door. -Stock "T" hose between headlights, GREAT shape, NO cracks.
-$25 shipped to your door. -Stock TT fuel rail with all 6 working 370cc stock injectors. I can Ohm test if you would like. Good upgrade for you NA guys, using Nitrous or for a cheap replacment for a bad TT injector.
-$200 shipped to your door. -Stock TT Carbon Canister. I removed mine to give me more room for my custom FMIC dual JWT filter intake. Worked great, great shape.
-$60 shipped to your door. -Stock EGR valve. I removed mine because I am doing a full turbo upgrade and did not want any emissions equipment. Worked perfectly before I removed it.
-$50 shipped to your door. -Stock TT, Starter/battery harness. Replaced mine because of doing full turbo upgrade. I wanted everything brand new. Nothing wrong with it.
-$27 shipped to your door. -Stock TT, 5spd Drive shaft. I had no vibration problems or center support bearing. I decided to upgrade to the One-piece Steel unit.
-$100+shipping (send me your zip code, so i can calculate shipping charges) -Two, 4-bolt Turbo--->down pipe metal NISSAN gasket. BRAND NEW, still in package.
-$25 shipped to your door -One 60U00 NISSAN 300zx spec oil filter, Brand new. Nissan discontinued these.
-$18 shipped to your door. -GReddy 300zx, Single Gauge pod,black w/ Metallic blue 'Greddy' embossed into plastic
and a Mechanical 52mm Greddy Boost gauge, Looks Great and is very accurate. White faced with a Metallic Dark blue bezel
-Both GReddy Pod and GReddy boost gauge $120 shipped to your door. -Great working Water pump, ~20k miles on it, NO play.
Replaced mine due to my recent build, Wanted everything brand new.
-$50 shipped to your door. -Great working timing belt tensioner ~20k miles on it. Replaced mine due to my recent build, Wanted everything brand new.
-$50 shipped to your door. -Great working TT oil pump, ~65k miles on it. They last for a LONG time, It even has a BRAND NEW Front MAIN CRANK SEAL, the seal has 0 miles on it. I just replaced my TTZ with new Oil pump because I wanted everything to be brand new on my current build. -Great working RPS SPORT 6-puck clutch w/ Pressure plate. I used this clutch for ~8k miles. I had to step up to the MAX, due to my larger turbos. Not much wear at all. Should have atleast another 20k miles on it w/out alot of drag racing. It is a VERY streetable clutch, I loved it, it's pedal pressure is hardly any more than stock.
-$200 shipped to your door. -Six BRAND NEW Pre-94' injector clips. Came off a BRAND NEW 91' EFI harness. I had to take them off to splic in my Border 850cc injector connectors
-$50 shipped to your door. -Stock TT Radiator, GREAT SHAPE, no cracks, leaks etc. I upgraded to a Z1/Howe racing radiator to cool down my engine due to my 4.5" thick GReddy Intercooler.
-$110+shipping. -Stock TT flywheel Great shape. I does not need to be resurfaced. I only used the RPS sport sprung 6 puck on it for ~8k miles. It has VERY minimal wear.
-$100, If you would like it to be resurfaced (it does not have to be though, its in really good shape) I can do it for another $50.
-So $100 As is... or $160 shipped to your door, resurfaced with the .035" step that is needed for TT's. -Stock TT rubber throttle body, intercooler hoses, Great shape, No cracks, holes. ALL 4.
-$47 shipped to your door. -Stock Detonation Sensor, USED, ~65k miles. Replaced mine because I wanted everything brand new. Worked perfectly fine when before I replaced it. Does NOT include harness.
-$60 shipped to your door. -Tension Rods, With BRAND NEW Energy Suspension Tension Rod bushings pressed into them. Ready to install! 0 Miles.
$115 shipped to your door. -Brand New steering Rack Energy Suspension Eurethane Bushings.
-$25 shipped to your door. -Razo, Aluminum/Magnesium, 5spd pedal set. These are the overlays. Very nice looking.
-$50 shipped to your door. Some prices are negotiable. I am always in the market for more mods and accessories. Let me know what you have to trade..... If you are interested in anything listed above, Look around for somthign you may consider trading, we can do a trade+cash or equal trade, etc.
*xamples of possible trades*..
Nitrous dry shot kit, Interchiller kit, purge nozzles ,MT ET drags/Streets, shift/E-Brake boots, HID headlight kits,Roll Cage (Auto-power or another company with the larger piping),Stillen GTZ-R front bumper, Stillen or Kaminari side skirts and door fillers, Kaminari rear valence. Working NA power steering pump, HICAS eliminator (SPL prefered), New window/T-top moldings or seals for TT or 2 seater, Black 94-96 Hatch or a black 90-96 hatch with ORIGINAL NISSAN GLASS!, ETC ETC ETC.
Just email me what you have and we'll go from there.
I would prefer to deal with someone local, but I will ship if needed.
Shawn300zTT (443-350-3130)
I dealt with many members on this board, They can attest for me, I am not a scammer etc.
-Dee Ridgeway
-Eric Taylor @ turbo-fx.com
-Arnel NJ
-Ashley Powers
-Tyler@ boostpro.net (MyZ8U)
-Chris@ boostpro.net
-Bernie Biliski
-Phuong (Got Rice)
-Shawn @ power supply racing
-Chris NJ
ETC ETC.
I will be out of town for the next week, until June 17th, Pictures are available for EVERYTHING, DO not ask for pictures if you are just 'wondering' of buying. Only if you are seriously interested.
Thanks! Let me know!
|
GT28R BOLT ON!!! LOADS of other Z parts....... - 
